m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3beta2 running on Duet 3 MB6HC v0.6 or 1.0 (SBC mode)
Board ID: 08DJM-956L2-G43S4-6J9D6-3SJ6M-KA6AG
Used output buffers: 7 of 40 (12 max)
=== RTOS ===
Static ram: 148476
Dynamic ram: 62228 of which 68 recycled
Never used RAM 143420, free system stack 117 words
Tasks: SENSORS(delaying,17) Linux(ready,145) HEAT(delaying,284) CanReceiv(notifyWait,773) CanSender(notifyWait,366) CanClock(delaying,341) TMC(notifyWait,58) MAIN(running,648) IDLE(ready,19)
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 02:07:48 ago, cause: software
Last software reset at 2021-04-01 17:24, reason: User, GCodes spinning, available RAM 144332, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task Linu Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
MCU temperature: min 41.4, current 44.3, max 47.2
Supply voltage: min 23.9, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 74889, ok, reads 10451, writes 23 timeouts 0, SG min/max 0/1023
Driver 1: position 4704, standstill, reads 10451, writes 23 timeouts 0, SG min/max 0/1023
Driver 2: position 5477, ok, reads 10449, writes 25 timeouts 0, SG min/max 0/1023
Driver 3: position 0, ok, reads 10449, writes 25 timeouts 0, SG min/max 0/1023
Driver 4: position 0, standstill, reads 10464, writes 11 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 10464, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2021-04-01 19:32:32
Slowest loop: 314.42ms; fastest: 0.04ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 1700622ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 11129, completed moves 11103, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 3, 2], CDDA state 3
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is doing "G1 X247.324005 Y245.031006 E1.212210" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0 0, running macro
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 152085, send timeouts 0, received 92147, lost 0, longest wait 79ms for reply type 6029, peak Tx sync delay 274, free buffers 49 (min 48)
=== SBC interface ===
State: 4, failed transfers: 0
Last transfer: 4ms ago
RX/TX seq numbers: 41689/41689
SPI underruns 0, overruns 0
Number of disconnects: 0, IAP RAM available 0x2d52c
Buffer RX/TX: 1472/2848-0
=== Duet Control Server ===
Duet Control Server v3.3-b2
File:
Buffered code: G1 X247.324 Y245.031 E1.21221
Buffered code: M204 S2000
Buffered code: G1 X246.718 Y244.335 F15000.000
Buffered code: M204 S1000
Buffered code: G1 F4800.000
Buffered code: G1 X263.165 Y244.335 E1.32675
Buffered code: G1 X263.165 Y260.665 E1.31729
Buffered code: G1 X246.718 Y260.665 E1.32675
Buffered code: G1 X246.718 Y244.425 E1.31003
Buffered code: M204 S2000
Buffered code: G1 X246.111 Y243.729 F15000.000
Buffered code: M204 S1000
Buffered code: G1 F3000.000
Buffered code: G1 X263.771 Y243.729 E1.42457
Buffered code: G1 X263.771 Y261.271 E1.41511
Buffered code: G1 X246.111 Y261.271 E1.42457
Buffered code: G1 X246.111 Y243.819 E1.40785
Buffered code: M204 S2000
Buffered code: G1 X246.691 Y243.883 F15000.000
Buffered code: G1 X247.567 Y247.534
Buffered code: G1 F4800.000
Buffered code: G1 X249.644 Y245.457 E0.23694
Buffered code: G1 X254.543 Y245.457 E0.39525
Buffered code: G1 X247.839 Y252.161 E0.76479
Buffered code: G1 X247.839 Y257.061 E0.39525
Buffered code: G1 X259.443 Y245.457 E1.32376
Buffered code: G1 X262.043 Y245.457 E0.20974
Buffered code: G1 X262.043 Y247.756 E0.18551
Buffered code: G1 X250.256 Y259.543 E1.34465
Buffered code: G1 X255.156 Y259.543 E0.39525
Buffered code: G1 X262.043 Y252.656 E0.78568
Buffered code: G1 X262.043 Y257.556 E0.39525
==> 1388 bytes
Code buffer space: 1400
Configured SPI speed: 8000000 Hz
Full transfers per second: 39.63
Codes per second: 12.03
Maximum length of RX/TX data transfers: 3572/1664
File /opt/dsf/sd/gcodes/X&Y&Stringing_test.gcode is selected, processing
4/1/2021, 7:32:24 PM	

m122 b21
Diagnostics for board 21:
Duet TOOL1LC firmware version 3.3beta2 (2021-03-10 10:06:22)
Bootloader ID: not available
Never used RAM 3984, free system stack 0 words
Tasks: Move(notifyWait,98) HEAT(delaying,77) CanAsync(notifyWait,63) CanRecv(notifyWait,75) CanClock(notifyWait,67) TMC(delaying,56) MAIN(running,348) AIN(delaying,63)
Last reset 02:07:38 ago, cause: software
Last software reset data not available
Driver 0: position 3592069, 409.0 steps/mm, ok, SG min/max 0/48, read errors 0, write errors 0, ifcnt 26, reads 37013, writes 1, timeouts 0, DMA errors 0, steps req 1015207 done 1015207
Moves scheduled 82558, completed 82558, in progress 0, hiccups 0, step errors 0, maxPrep 634, maxOverdue 0, maxInc 0, mcErrs 0, gcmErrs 0
Peak sync jitter 9, peak Rx sync delay 222, resyncs 4, no step interrupt scheduled
VIN: 24.0V
MCU temperature: min 40.6C, current 53.2C, max 56.5C
Ticks since heat task active 235, ADC conversions started 7633922, completed 7633921, timed out 0
Last sensors broadcast 0x00000004 found 1 24 ticks ago, loop time 0
CAN messages queued 26154, send timeouts 0, received 29783, lost 0, free buffers 36, min 35, error reg 0
dup 0, oos 0, bm 0, wbm 0