4/13/2021, 11:47:25 AM	m122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.3beta1 running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: 9D67T-3096U-D65J0-40KMW-K203Z-HJTTJ
Used output buffers: 3 of 40 (14 max)
=== RTOS ===
Static ram: 98792
Dynamic ram: 115180 of which 84 recycled
Never used RAM 27656, free system stack 124 words
Tasks: NETWORK(ready,228) SENSORS(delaying,25) HEAT(notifyWait,293) CanReceiv(notifyWait,944) CanSender(notifyWait,357) CanClock(delaying,341) TMC(notifyWait,99) MAIN(running,332) IDLE(ready,20) AIN(notifyWait,260)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:51:11 ago, cause: software
Last software reset at 2021-04-13 10:56, reason: User, GCodes spinning, available RAM 27656, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
Supply voltage: min 0.0, current 23.9, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 48000, ok, SG min/max 0/40, read errors 0, write errors 1, ifcnt 25, reads 37449, writes 13, timeouts 158, DMA errors 0, failedOp 0x01
Driver 1: position -1253, standstill, SG min/max 0/462, read errors 0, write errors 1, ifcnt 40, reads 37602, writes 17, timeouts 1, DMA errors 0, failedOp 0x71
Driver 2: position 14752, standstill, SG min/max 0/488, read errors 0, write errors 1, ifcnt 40, reads 37586, writes 17, timeouts 17, DMA errors 0, failedOp 0x01
Driver 3: position 0, standstill, SG min/max 0/510, read errors 0, write errors 1, ifcnt 38, reads 37603, writes 17, timeouts 0, DMA errors 0
Driver 4: position 0, ok, SG min/max 0/510, read errors 0, write errors 1, ifcnt 39, reads 37594, writes 18, timeouts 8, DMA errors 0, failedOp 0x71
Driver 5: position 0, standstill, SG min/max 0/466, read errors 0, write errors 1, ifcnt 40, reads 37562, writes 17, timeouts 41, DMA errors 0, failedOp 0x06
Driver 6: position 0, standstill, SG min/max 0/454, read errors 0, write errors 1, ifcnt 40, reads 37597, writes 17, timeouts 6, DMA errors 0, failedOp 0x06
Date/time: 2021-04-13 11:47:24
Cache data hit count 4108298769
Slowest loop: 105.54ms; fastest: 0.10ms
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 99.9ms, write time 5.3ms, max retries 0
=== Move ===
DMs created 83, maxWait 426133ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 29436, completed moves 29410, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 550, 1], CDDA state 3
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.2
Heater 1 is on, I-accum = 0.4
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is doing "G1 F1200" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: ok
=== CAN ===
Messages queued 27693, send timeouts 27690, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 17 (min 17)
=== Network ===
Slowest loop: 107.57ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.25
WiFi MAC address f4:cf:a2:6f:bd:e6
WiFi Vcc 3.31, reset reason Power up
WiFi flash size 2097152, free heap 21944
WiFi IP address 10.0.0.11
WiFi signal strength -61dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0