; Configuration file for Duet Maestro (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.2.3 on Thu Apr 15 2021 21:59:27 GMT+0200 (Mitteleuropäische Sommerzeit) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Kossel XL" ; set printer name M665 R181.59 L300.187 B116 H441.06 ; Set delta radius, diagonal rod length, printable radius and homed height M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them M912 P0 S-9.1 ; MCU temperature sensor calibration offset ; Network M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP M586 P0 S1 ; enable HTTP M586 P1 S1 ; enable FTP M586 P2 S1 ; enable Telnet ; Drives M569 P0 S1 D3 V50 ; physical drive 0 goes forwards M569 P1 S1 D3 V50 ; physical drive 1 goes forwards M569 P2 S1 D3 V50 ; physical drive 2 goes forwards M569 P3 S1 ; physical drive 3 goes forwards M584 X0 Y1 Z2 E3 ; set drive mapping M350 X32 Y32 Z32 E32 I0 ; configure microstepping without interpolation M92 X320 Y320 Z320 E1610 ; set steps per mm M566 X600 Y600 Z600 E600 ; set maximum instantaneous speed changes (mm/min) M203 X15000 Y15000 Z15000 E3600 ; set maximum speeds (mm/min) M201 X1500 Y1500 Z1500 E1500 ; set accelerations (mm/s^2) M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 Z0 S1 ; set minimum Z ; Endstops M574 X2 S1 P"!^xstop" ; configure active-high endstop for high end on X via pin !^xstop M574 Y2 S1 P"!^ystop" ; configure active-high endstop for high end on Y via pin !^ystop M574 Z2 S1 P"!^zstop" ; configure active-high endstop for high end on Z via pin !^zstop ; Z-Probe M558 P5 R0.4 C"zprobe.in" H2.5 F240 T1500 ; set Z probe type to effector and the dive height + speeds G31 P1 X0 Y0 Z-0.1 ; set Z probe trigger value, offset and trigger height M557 R110 S45 ; define mesh grid ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S90 ; set temperature limit for heater 0 to 90C M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M143 H1 S275 ; set temperature limit for heater 1 to 275C ; Fans M950 F0 C"fan0" Q65535 ; create fan 0 on pin fan0 and set its frequency M106 P0 C"Part cooling Fan R" S1 H-1 ; set fan 0 name and value. Thermostatic control is turned off M950 F1 C"fan1" Q65535 ; create fan 1 on pin fan1 and set its frequency M106 P1 C"Hotend Fan " S1 H1 T45 ; set fan 1 name and value. Thermostatic control is turned on M950 F2 C"fan2" Q65535 ; create fan 2 on pin fan2 and set its frequency M106 P2 C"Part cooling Fan L" S1 H-1 ; set fan 2 name and value. Thermostatic control is turned off ; Tools M563 P0 S"E3D V6" D0 H1 F0:1:2 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings M591 D0 P1 C"e0_stop" s1 ; filament monitor connected to E0_stop M81 ; PSU off G29 S1 ; Load hight map ; Miscellaneous M501 ; load saved parameters from non-volatile memory T0 ; select first tool