; Configuration file for Duet WiFi (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2.1.4 on Mon Jan 06 2020 13:06:19 GMT+0100 (Ora standard dell’Europa centrale) ; General preferences G21 ; Works in millimiters G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M555 P1 ; Set firmware compatibility to look like RepRap Firmware M665 L400.25:400.25:400.25 R165 B170 H492 ; Set delta radius, diagonal rod length, printable radius and homed height (With extra glass 23/09/2020) M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them M575 P1 B57600 S1 ; set paneldue communication parameters ; Network M550 P"TEVO Little Monster" ; Set machine name M552 S1 ; Enable network M586 P0 S1 ; Enable HTTP M586 P1 S1 ; Enable FTP M586 P2 S0 ; Disable Telnet ; Drives M569 P0 S0 ; physical drive 0 goes backwards M569 P1 S0 ; physical drive 1 goes backwards M569 P2 S0 ; physical drive 2 goes backwards M569 P3 S0 ; physical drive 3 goes backwards M584 X0.0 Y0.1 Z0.2 E0.3 ; set drive mapping M579 X1.00806 Y1.007252 Z1.0040 ; Scale parameter for axes X, Y and Z calculated on 16/05/2020 M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X160.00 Y160.00 Z160.00 E831.815 ; set steps per mm M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min) M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min) M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2) M906 X1250 Y1250 Z1250 E1200 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 Z0 S1 ; set minimum Z ; Endstops M574 X2 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop M574 Y2 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop M574 Z2 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop ; Z-Probe M558 P8 R0.8 C"zprobe.in+zprobe.mod" H5 A5 F1200 T6000 ; set Z probe type to effector and the dive height + speeds (New setting from 15/05/2020) G31 P100 X0 Y0 Z-0.135 ; set Z probe trigger value, offset and trigger height M557 R155 S15 ; define mesh grid (New setting from the old config.g) ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 R4700 A"Piatto" ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M140 H0 ; define and create the bed heater (set on 13/05/2020, needed with RRF 3) M143 H0 S120 ; set temperature limit for heater 0 to 120C M307 H0 R0.281 C734.9 D2.10 S1.00 V23.9 ; disable bang-bang mode for the nozzle heater and set PWM limit M308 S1 P"e0temp" Y"thermistor" T100000 B4725 R4375 C7.06e-8 A"Ugello" ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M143 H1 S280 ; set temperature limit for heater 1 to 280C M307 H1 R1.416 C215.9 D5.53 S1.00 V23.7 ; disable bang-bang mode for the nozzle heater and set PWM limit ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 C"Part cooling fan" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 C"Hotend fan" S1 H1 T45 ; set fan 1 name and value. Thermostatic control is turned on ; Tools M563 P0 D0 H1 F-1 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Filament run-out sensor M591 D0 P2 C"e0_stop" S1 ; Filament run-out sensor Input high when filament is in / Filament monitor connected to E0_stop ; Automatic power saving M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss ; Miscellaneus M375 ; Load the grid probing mesh M501 ; read stored parameters from config override M572 D0 S0.20 ; set extruder 0 pressure advance to 0.20 seconds (E3D Volcano wih Nozzle-X 0.4mm and bondtech extruder on 08/04/2020)