@phaedrux said in [X turned down, replacig with E?](/post/230176):
> M122




9.5.2021 klo 21.55.55	M98 P"config.g"
Error: Bad command: 0:/sys/config.g
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 480C.
Warning: Heater 2 appears to be over-powered. If left on at full power, its temperature is predicted to reach 524C.
Error: G10: Attempt to set/report offsets and temperatures for non-existent tool: 2
Error: Bad command: Leapfrog-Duet
Error: Bad command: Send code...
Error: Bad command: Status
Error: Bad command: Idle
No tool is selected
Error: Bad command: X
Error: Bad command: 0.0
Error: Bad command: Y
Error: Bad command: 0.0
Error: Bad command: Z
Error: Bad command: 0.00
Error: Bad command: Extruder Drives
Error: Bad command: Drive 0
Error: Bad command: 0.0
Error: Bad command: Speeds
Error: Bad command: Requested Speed
Error: Bad command: 0 mm/s
No tool is selected
Error: Bad command: 0 mm/s
Error: Bad command: Sensors
Error: Bad command: Vin
Error: Bad command: 24.1 V
Error: Bad command: MCU Temperature
Error: Bad command: 32.5 C
Error: Bad command: Fan RPM
Error: Bad command: 0
No tool is selected
Error: Bad command: Extra
Error: Bad command: Control All
No tool is selected
Error: Bad command: off	23.4 C	
Error: Bad command: -273.1
Error: Bad command: -273.1
Error: Bad command: Bed	Heater 0
Error: Bad command: off	22.4 C	
Error: Bad command: 0
Error: Bad command: 0
Error: Bad command: System Directory





9.5.2021 klo 21.53.53	M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
Board ID: 08DGM-956GU-DJ3SW-6JKDG-3SD6N-1UM3G
Used output buffers: 3 of 24 (10 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 93436 of which 0 recycled
Exception stack ram used: 320
Never used ram: 11604
Tasks: NETWORK(ready,628) HEAT(blocked,1232) MAIN(running,3724) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:15:09 ago, cause: power up
Last software reset time unknown, reason: User, spinning module GCodes, available RAM 11612 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 27.1, current 32.7, max 33.0
Supply voltage: min 24.0, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2021-05-09 21:53:52
Cache data hit count 2787129665
Slowest loop: 12.54ms; fastest: 0.06ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.54ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address bc:dd:c2:63:69:18
WiFi Vcc 3.38, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 24360
WiFi IP address 192.168.1.11
WiFi signal strength -49dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0