; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M555 P1 ; Set firmware compatibility to look like RepRapFirmare ;*** The homed height is deliberately set too high in the following - you will adjust it during calibration. M665 R120 L269 B120 H385 ; Set delta radius, diagonal rod length, printable radius and homed height M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them ; Network M550 Duet ; Set machine name M552 S1 ; Enable network M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Drives M569 P0 S1 ; X Tower Drive 0 goes forwards M569 P1 S0 ; Y Tower Drive 1 goes backwards M569 P2 S1 ; Z Tower Drive 2 goes forwards M569 P3 S1 ; Extruder 1 Drive 3 goes forwards E0 M569 P4 S0 ; Extruder 1 Drive 3 goes forwards E1 M350 X16 Y16 Z16 E16:16 I1 ; Configure microstepping with interpolation M92 X80 Y80 Z80 E94.023 ; Set steps per mm M566 X72000 Y72000 Z72000 E1200:1200 ; Set maximum instantaneous speed changes (mm/min) M203 X1200000 Y1200000 Z1200000 E3600:3600 ; Set maximum speeds (mm/min) M201 X1000 Y1000 Z1000 E1000:1000 ; Set accelerations (mm/s^2) M906 X1300 Y1300 Z1300 E1200:1200 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 Z0 S1 ; Set minimum Z ; Endstops M574 X2 Y2 Z2 S1 ; Set active high endstops ; Z-Probe M558 P1 X0 Y0 Z0 H25 F120 T6000 ; Set Z probe type to modulated, the axes for which it is used and the dive height + speeds G31 P500 X0 Y0 Z2.599 ; Set Z probe trigger value, offset and trigger height M557 R145 S20 ; Define mesh ; Heaters M305 P0 T100000 B4338 C0 R4700 ; Set thermistor + ADC parameters for heater 0 M143 H0 S110 ; Set temperature limit for heater 0 to 110C M305 P1 X200 ; Configure thermocouple for heater 1 M143 H1 S280 ; Set temperature limit for heater 1 to 280C ; Fans M106 P0 S1 I0 F500 H1 T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on M106 P1 S0 I0 F500 H-1. ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off ;M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on ; Tools M563 P0 D0 H1 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Custom settings are not configured M563 P1 D1 H1 ; Define tool 1 G10 P1 X0 Y0 Z0 ; Set tool 1 axis offsets G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C ; Custom settings are not configured