; Fusion3 F410 Firmware configuration file
; For FusionWare 1.18.1
; Revision 2018.08.22
; For Serial Number 5465

M111 S0                             	; Debug off
M550 PFusion3 F410		        		; Machine name MUST HAVE A "P" IN FRONT OF IT(can be anything you like)
M551 Pfusion3                       	; Machine password MUST HAVE A "P" IN FRONT OF IT
M540 P0xBE:0xEF:0xDE:0xAD:0x54:0x65 	; MAC Address (replace last 2 blocks with 4 digit s/n)
;=== Adjust the following 3 lines to suit your network ===
M552 P0.0.0.0 S1						; IP address (0 = use DHCP)
M554 P192.168.1.1                   	; Gateway
M553 P255.255.255.0                 	; Netmask
;=========================================================
M555 P2                             	; Set output to look like Marlin
M575 P1 B57600 S1						; comms params for paneldue

; Machine configuration
M569 P0 S1							; Drive 0 goes forwards
M569 P1 S0							; Drive 1 goes backwards
M569 P2 S0							; Drive 2 goes backwards
M569 P3 S0							; Drive 3 goes backwards
M569 P4 S0							; Drive 4 goes backwards
M574 X1 Y1 Z2 S1					; set endstop configuration
M667 S1								; set CoreXY mode
M92 X43.70 Y43.70 Z426.67 E190.0	; set axis steps/mm
M906 X1300 Y1300 Z1400 E1400 I100   ; Set motor currents (mA)
M201 X2000 Y2000 Z300 E4000	        ; Accelerations (mm/s^2)
M203 X33000 Y33000 Z2500 E10000     ; Maximum speeds (mm/min)
M566 X600 Y600 Z40 E950	     		; Maximum jerk speeds mm/minute
M208 X355 Y355 Z315					; set axis maxima
M208 X0 Y0 Z0 S1					; set axis minima 
G21									; work in mm
G90									; absolute coords
M83									; relative extruder movements

; Z probe
M558 P5 X0 Y0 Z0 H7 F100            ; Set probe type and if it's used for axis homing (no in our case)
G31 Z0.10 P600                      ; Set the probe height and threshold (smaller number = further away from bed)

; Thermistors and heaters
M305 P0 T100000 B4036 R4700 				
M305 P1 T100000 B4725 C7.06e-8 R4700 		
M305 P2 T100000 B4725 C7.06e-8 R4700 

M307 H0 A153.5 C534.2 D6.7 B0			; Configure H0 (bed) heater model
M307 H1 A483.4 C190.2 D6.6 B0			; Configure H1 (print head) heater model

M143 S320								; Set max print head temperature
M143 H0 S140							; Set max heat bed temperature
M570 H1 P10 T15							; Configure heater safety timeouts

; Tool definition
M563 P0 D0 H1                       ; Define tool 0
G10 P0 S0 R0		                ; Set tool 0 operating and standby temperatures
M563 P2 H0							; define heat bed tool
G10 P2 S0 R0						; define heat bed tool op and standby temps
;M572 D0 S0.20

; Configure filament monitor
M581 T2 E0 S0 C1

; Reset filament monitor when the board is rebooted
M42 P63 S0
G4 P50
G4 P50
M42 P63 S1

T0									; select first hot end