31.8.2021, 0:13:06: Connected to 10.100.102.23
31.8.2021, 0:14:37: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 0:14:52: Connection established
31.8.2021, 0:15:02: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-9P63L-DJ3T8-6J1D6-3SJ6K-1A7HA
Used output buffers: 3 of 40 (11 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 92104 of which 0 recycled
Never used RAM 111184, free system stack 206 words
Tasks: NETWORK(ready,30.0%,212) ETHERNET(notifyWait,0.1%,117) HEAT(notifyWait,0.0%,325) Move(notifyWait,0.0%,302) CanReceiv(notifyWait,0.0%,944) CanSender(notifyWait,0.0%,374) CanClock(delaying,0.0%,343) TMC(notifyWait,7.6%,93) MAIN(running,62.0%,1096) IDLE(ready,0.4%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:00:27 ago, cause: power up
Last software reset at 2021-08-30 23:36, reason: User, GCodes spinning, available RAM 111184, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 167
MCU temperature: min 31.5, current 37.2, max 37.4
Supply voltage: min 24.0, current 24.0, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.2, max 12.3, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, reads 20944, writes 14 timeouts 0, SG min/max 0/0
Driver 1: position 0, standstill, reads 20944, writes 14 timeouts 0, SG min/max 0/0
Driver 2: position 0, standstill, reads 20944, writes 14 timeouts 0, SG min/max 0/0
Driver 3: position 0, standstill, reads 20945, writes 14 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 20945, writes 14 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 20946, writes 14 timeouts 0, SG min/max 0/0
Date/time: 2021-08-31 00:15:01
Slowest loop: 9.16ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 2.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 247, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 49 (min 49), ts 138/0/0
Tx timeouts 0,0,137,0,0,108 last cancelled message type 4514 dest 127

=== Network ===
Slowest loop: 14.35ms; fastest: 0.02ms
Responder states: HTTP(4) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 3 2 2 2 0 0 0
31.8.2021, 0:15:50: Upload of config.g successful after 0s
31.8.2021, 0:15:55: Emergency stop, attemping to reconnect...
31.8.2021, 0:16:04: Connection interrupted, attempting to reconnect...
31.8.2021, 0:16:12: Connection established
31.8.2021, 0:22:42: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 1:21:14: Connection established
31.8.2021, 1:23:45: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 1:25:38: Connection established
31.8.2021, 1:26:27: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 1:27:22: Connection established
31.8.2021, 1:28:45: G92 Z0
31.8.2021, 1:30:09: G30 S-1: Error: G30: Insufficient axes homed for bed probing
31.8.2021, 1:31:23: G30 S-1: Stopped at height 0.312 mm
31.8.2021, 1:31:32: G30 S-1: Error: Probe already triggered at start of probing move
31.8.2021, 1:32:03: Upload of config.g successful after 0s
31.8.2021, 1:32:13: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 1:32:22: Connection established
31.8.2021, 1:33:08: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 1:34:27: Connection established
31.8.2021, 1:34:48: G92 Z0
31.8.2021, 1:35:45: G30 S-1: Error: G30: Insufficient axes homed for bed probing
31.8.2021, 1:35:50: G30 S-1: Error: G30: Insufficient axes homed for bed probing
31.8.2021, 1:35:54: G30 S-1: Error: G30: Insufficient axes homed for bed probing
31.8.2021, 1:37:26: G30 S-1: Stopped at height 0.519 mm
31.8.2021, 1:39:18: G92 Z0
31.8.2021, 1:41:46: Upload of config.g successful after 0s
31.8.2021, 1:41:49: Emergency stop, attemping to reconnect...
31.8.2021, 1:41:57: Connection interrupted, attempting to reconnect...
31.8.2021, 1:42:05: Connection established
31.8.2021, 1:47:40: G30
31.8.2021, 1:48:51: Upload of config.g successful after 0s
31.8.2021, 1:48:56: Emergency stop, attemping to reconnect...
31.8.2021, 1:49:04: Connection interrupted, attempting to reconnect...
31.8.2021, 1:49:12: Connection established
31.8.2021, 1:49:36: Upload of config.g successful after 0s
31.8.2021, 1:49:38: Emergency stop, attemping to reconnect...
31.8.2021, 1:49:47: Connection interrupted, attempting to reconnect...
31.8.2021, 1:49:56: Connection established
31.8.2021, 1:51:21: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 1:53:09: Connection established
31.8.2021, 1:54:17: Upload of homeall.g successful after 0s
31.8.2021, 1:54:28: Upload of config.g successful after 0s
31.8.2021, 1:54:35: Emergency stop, attemping to reconnect...
31.8.2021, 1:54:43: Connection interrupted, attempting to reconnect...
31.8.2021, 1:54:52: Connection established
31.8.2021, 2:03:09: G30
31.8.2021, 2:05:52: G30
31.8.2021, 2:07:26: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 2:07:38: Connection established
31.8.2021, 2:09:48: Upload of config.g successful after 0s
31.8.2021, 2:09:51: Emergency stop, attemping to reconnect...
31.8.2021, 2:09:59: Connection interrupted, attempting to reconnect...
31.8.2021, 2:10:07: Connection established
31.8.2021, 2:15:04: Upload of config.g successful after 0s
31.8.2021, 2:15:16: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 2:15:25: Connection established
31.8.2021, 2:15:57: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 2:16:13: Connection established
31.8.2021, 2:16:46: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 2:19:39: Connection established
31.8.2021, 2:20:03: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 2:21:18: Connection established
31.8.2021, 2:25:26: Upload of config.g successful after 0s
31.8.2021, 2:25:39: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 2:25:40: Failed to download config.g: Could not complete action because the connection has been terminated
31.8.2021, 2:25:48: Connection established
31.8.2021, 2:26:14: Upload of config.g successful after 0s
31.8.2021, 2:26:25: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 2:26:34: Connection established
31.8.2021, 2:27:20: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 2:27:33: Connection established
31.8.2021, 2:27:49: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 2:29:06: Connection established
31.8.2021, 2:29:26: Upload of config.g successful after 0s
31.8.2021, 2:29:38: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 2:29:47: Connection established
31.8.2021, 2:33:53: Connection interrupted, attempting to reconnect...: HTTP request timed out
31.8.2021, 2:35:01: Connection established
31.8.2021, 2:35:23: M98 P"config.g": Error: Bad command: M
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: Invalid use of P parameter
31.8.2021, 2:35:29: M98 P"config.g": Error: Bad command: M
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: Invalid use of P parameter
31.8.2021, 2:35:47: M98 P"config.g": Error: Bad command: M
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: Invalid use of P parameter
31.8.2021, 2:35:54: M98 P"config.g": Error: Bad command: M
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: Invalid use of P parameter
31.8.2021, 2:46:44: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-9P63L-DJ3T8-6J1D6-3SJ6K-1A7HA
Used output buffers: 3 of 40 (12 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 92096 of which 44 recycled
Never used RAM 111148, free system stack 206 words
Tasks: NETWORK(ready,30.2%,212) ETHERNET(notifyWait,0.1%,117) HEAT(delaying,0.0%,325) Move(notifyWait,0.0%,302) CanReceiv(notifyWait,0.0%,944) CanSender(notifyWait,0.0%,374) CanClock(delaying,0.0%,333) TMC(notifyWait,7.6%,93) MAIN(running,62.0%,1096) IDLE(ready,0.0%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:12:00 ago, cause: power up
Last software reset at 2021-08-31 02:29, reason: User, GCodes spinning, available RAM 111148, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 183
MCU temperature: min 28.3, current 40.1, max 40.2
Supply voltage: min 24.0, current 24.0, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 11.4, current 12.2, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, reads 12988, writes 26 timeouts 0, SG min/max 0/0
Driver 1: position 0, standstill, reads 12988, writes 26 timeouts 0, SG min/max 0/0
Driver 2: position 0, standstill, reads 12988, writes 26 timeouts 0, SG min/max 0/0
Driver 3: position 0, standstill, reads 12988, writes 26 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 12989, writes 26 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 12989, writes 26 timeouts 0, SG min/max 0/0
Date/time: 2021-08-31 02:46:43
Slowest loop: 8.70ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 2.1ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 6486, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 49 (min 49), ts 3604/0/0
Tx timeouts 0,0,3603,0,0,2881 last cancelled message type 4514 dest 127

=== Network ===
Slowest loop: 14.03ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 2 2 2 2 0 0 0