; Configuration file for Duet WiFi (firmware version 3.3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.3.2 on Fri Sep 10 2021 08:45:36 GMT+0300 (Israel Daylight Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"SK-GO2" ; set printer name M669 K1 ; select CoreXY mode ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ;Ernst Drives ;M569 P0 S1 D2 ; physical drive 0 goes backwards using default driver timings ;M569 P1 S1 D2 ; physical drive 1 goes backwards using default driver timings ;M569 P2 S1 ; physical drive 2 goes forwards using default driver timings ;M569 P3 S0 ; physical drive 3 goes forwards using default driver timings ;M569 P4 S1 ; physical drive 4 goes backwards using default driver timings ;M569 P5 S1 ; physical drive 5 goes forwards using default driver timings ;M584 X0 Y1 Z2:4:5 E3 ; set drive mapping ; ==========Drives M569 P0 S1 ; physical drive 0 goes forwards M569 P1 S1 ; physical drive 1 goes forwards M569 P2 S0 ; physical drive 2 goes backwards M569 P3 S0 ; physical drive 3 goes forwards M584 X0 Y1 Z2 E3 ; set drive mapping M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X200.00 Y200.00 Z3200.00 E408 ; set steps per mm M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X30000.00 Y30000.00 Z450.00 E6000.00 ; set maximum speeds (mm/min) M201 X2000.00 Y2000.00 Z100.00 E2000.00 ; set accelerations (mm/s^2) M906 X800 Y800 Z600 E550 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ;;M671 X-13:-13:323 Y20:250:140 S50 ; set z drive coordinates ;;M350 X16 Y16 Z16:16:16 E16 I1 ; configure microstepping with interpolation ;;M92 X200.00 Y200.00 Z160.00 E420.00 ; set steps per mm ;;M566 X600.00 Y600.00 Z24.00 E300.00 ; set maximum instantaneous speed changes (mm/min) ;;M203 X30000.00 Y30000.00 Z2400.00 E2400.00 ; set maximum speeds (mm/min) ;;M201 X2000.00 Y2000.00 Z200.00 E2000.00 ; set accelerations (mm/s^2) ;;M906 X800 Y800 Z600 E800 I30 ; set motor currents (mA) and motor idle factor in per cent ;;M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X305 Y305 Z340 S0 ; set axis maxima ; Endstops M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop ; Z-Probe M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed M557 X15:215 Y15:195 S20 ; define mesh grid ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit M307 H0 B0 R0.413 C530.0 D9.48 S1.00 V24.2 M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M307 H1 B0 R2.328 C205.0 D5.24 S1.00 V24.1 M143 H1 S250 ; set temperature limit for heater 1 to 250C ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 C"part_fan" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 C"ext_fan" S1 H1 T40 ; set fan 1 name and value. Thermostatic control is turned on ; Tools M563 P0 S"main" D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings M575 P1 B57600 M501 ; Miscellaneous T0 ; select first tool