Container Stack: Extruder 1
type	extruder_train
id	custom_extruder_1 #2
name	Extruder 1
definition	custom
quality_type	draft
read only	False
path	C:\Users\Franken\AppData\Roaming\cura\4.11\extruders\custom_extruder_1+%232.extruder.cfg
?? Cross Fill Density Image for Support	''
?? Cubic Subdivision Shell	0.4
?? Print Acceleration	700
?? Top Surface Skin Pattern	'lines'
?? Minimum Support Roof Area	1.0
?? Top/Bottom	0
?? Outer Wall Jerk	35
?? Break Preparation Temperature	230
?? WP Ease Upward	0.3
?? Wall Line Count	3
?? Support Floor Line Width	0.4
?? Gantry Height	660
?? WP Flat Flow	100
?? Minimum Support Interface Area	1.0
?? Support Floor Line Directions	'[ ]'
?? Infill Line Directions	'[ ]'
?? Brim Line Count	20
?? Ironing Line Spacing	0.1
?? Supported Skin Fan Speed	100
?? Mold Roof Height	0.5
?? Minimum Volume Before Coasting	0.8
?? Print Speed	50
?? Spiralize Outer Contour	False
?? Experimental	0
?? Maximum Resolution	0.5
?? Wipe Nozzle Between Layers	False
?? Break Preparation Retraction Speed	2
?? Top/Bottom Flow	100
?? Support Roof Jerk	35
?? WP Connection Height	3
?? Speed	0
?? Special Modes	0
?? Initial Layer Speed	15
?? Compensate Outer Wall Overlaps	True
?? Monotonic Top/Bottom Order	True
?? Flow Temperature Graph	'[[3.5,200],[7.0,240]]'
?? Support Roof Speed	23.333333333333332
?? Raft Middle Print Speed	18.75
?? Minimum Wall Flow	0
?? Infill Extruder	'-1'
?? Quality	0
?? Brim Distance	0
?? WP Bottom Delay	0
?? Absolute Extruder Prime Position	False
?? Mesh Rotation Matrix	'[[1,0,0], [0,1,0], [0,0,1]]'
?? Support Interface Acceleration	700
?? Build Plate Material	'glass'
?? Support Infill Acceleration	700
?? Raft Base Thickness	0.24
?? Fan Speed	55
?? Bridge Has Multiple Layers	False
?? Make Overhang Printable	False
?? Maximum Filament Acceleration	10000
?? Travel	0
?? Wipe Z Hop Height	2
?? Outer Wall Wipe Distance	0.2
?? Bridge Skin Speed	12.5
?? Initial Layer Print Acceleration	700
?? Standby Temperature	205.0
?? Initial Layer Print Speed	15
?? Support Z Distance	0.1
?? WP Nozzle Clearance	1
?? Retract at Layer Change	True
?? Default Acceleration	4000
?? Retract Before Outer Wall	True
?? Prime Tower Size	20
?? Prime Tower Jerk	35
?? Skin Overlap	0.02
?? Top/Bottom Speed	25.0
?? WP Horizontal Printing Speed	5
?? Skin Edge Support Thickness	0
?? Support Infill Line Directions	'[ ]'
?? Bridge Second Skin Speed	12.5
?? Extruders Share Heater	False
?? Raft Top Print Jerk	35
?? Wipe Hop Speed	10
?? Raft Middle Spacing	1.0
?? Mold	False
?? Raft Top Fan Speed	0
?? Layer Height	0.2
?? Build Plate Temperature Initial Layer	85
?? Scene Has Support Meshes	False
?? Infill Before Walls	True
?? Draft Shield X/Y Distance	10
?? Raft Middle Fan Speed	0
?? Support Interface Line Width	0.4
?? Connect Top/Bottom Polygons	False
?? Support Roof Acceleration	700
?? None	0
?? Minimum Support Floor Area	1.0
?? Prime Tower Minimum Volume	6
?? Use Adaptive Layers	False
?? Bridge Third Skin Flow	110
?? Bridge Third Skin Speed	12.5
?? Support Placement	'buildplate'
?? Extruders Share Nozzle	False
?? Enable Coasting	False
?? Fuzzy Skin	False
?? No Load Move Factor	0.940860215
?? Support Roof Pattern	'concentric'
?? Raft Top Layers	2
?? Bridge Third Skin Fan Speed	0
?? Z Hop Height	2
?? Top/Bottom Extruder	'-1'
?? Maximum Acceleration Y	9000
?? Ironing Jerk	35
?? Adaptive Layers Variation Step Size	0.01
?? WP Drag Along	0.6
?? Support Structure	'normal'
?? Build Plate Adhesion Extruder	0
?? Support Floor Pattern	'concentric'
?? Fuzzy Skin Outside Only	False
?? Material Volume Between Wipes	10
?? Adhesion Tendency	10
?? Raft Top Print Speed	25.0
?? Support Pattern	'zigzag'
?? Enable Support Brim	False
?? Raft Base Print Jerk	35
?? Inner Wall Extruder	'-1'
?? Bridge Fan Speed	90
?? Z Hop After Extruder Switch	True
?? Infill Line Width	0.4
?? Linear Advance Factor	0
?? Support Interface Jerk	35
?? Diameter	1.75
?? Compensate Inner Wall Overlaps	True
?? Wait for Nozzle Heatup	True
?? Raft Top Spacing	0.4
?? Z Seam Alignment	'sharpest_corner'
?? Extra Skin Wall Count	1
?? Infill Acceleration	700
?? Break Retraction Speed	25
?? Initial Bottom Layers	4
?? Support Bottom Distance	0
?? Monotonic Top Surface Order	True
?? Enable Prime Blob	False
?? Raft Base Print Acceleration	700
?? Support Interface Density	100
?? Smooth Spiralized Contours	True
?? WP Roof Inset Distance	3
?? Machine Height	660
?? Brim Replaces Support	True
?? WP Upward Printing Speed	5
?? Support Mesh	False
?? Retraction Extra Prime Amount	-0.1
?? Support Wall Line Count	1
?? Layer Start X	0.0
?? Wire Printing	False
?? Minimum Support X/Y Distance	0.2
?? Maximum Speed Y	299792458000
?? Connect Support ZigZags	True
?? Inner Wall Jerk	35
?? Material GUID	'b4cd8cf7-2e98-44bd-9e4c-600b5d339e54'
?? None	0
?? Support Stair Step Height	0.3
?? Support Interface Extruder	0
?? Keep Disconnected Faces	False
?? Wipe Retraction Enable	True
?? Default X-Y Jerk	20.0
?? Optimize Wall Printing Order	True
?? Brim Width	8.0
?? Mesh Processing Rank	0
?? Steps per Millimeter (Y)	50
?? Bottom Skin Removal Width	1.2000000000000002
?? Infill Jerk	35
?? Support Roof Line Width	0.4
?? Maximum Feedrate	299792458000
?? End of Filament Purge Speed	0.5
?? Slicing Tolerance	'middle'
?? Support Floor Thickness	1
?? Offset with Extruder	True
?? Regular Fan Speed at Height	0.2
?? Support Roof Line Distance	0.4
?? Generate Support	False
?? Raft Middle Line Width	0.8
?? Seam Corner Preference	'z_seam_corner_any'
?? Tree Support Branch Diameter Angle	5
?? WP Straighten Downward Lines	20
?? WP Speed	5
?? Disallowed Areas	[]
?? Infill Line Distance	4.0
?? Avoid Printed Parts When Traveling	True
?? Ironing Speed	16.666666666666668
?? Inner Wall Linear Advance Factor	0
?? Minimum Bridge Wall Length	5
?? Printing Temperature Initial Layer	230
?? Anti-ooze Retraction Speed	5
?? Bridge Wall Flow	85
?? Minimal Mold Width	5
?? Support Roof Horizontal Expansion	0.0
?? Brim Only on Outside	True
?? Raft Extra Margin	15
?? Raft Air Gap	0.3
?? Support Infill Extruder	0
?? Horizontal Expansion	0
?? Z Hop Only Over Printed Parts	False
?? Build Plate Shape	'rectangular'
?? Top/Bottom Acceleration	700
?? Top Surface Skin Line Directions	'[ ]'
?? Flow Rate Compensation Factor	100
?? Initial Layer Linear Advance Factor	0
?? Enable Ironing	True
?? Bridge Wall Speed	17
?? Nozzle Diameter	0.4
?? Skin Edge Support Layers	0
?? Regular Fan Speed	75
?? Infill Line Multiplier	1
?? Merged Meshes Overlap	0.15
?? Skin Expand Distance	1.2000000000000002
?? Support Interface Resolution	0.3
?? Z Hop When Retracted	False
?? Support Overhang Angle	35
?? Support	0
?? Machine Depth	330
?? Wipe Brush X Position	100
?? Infill Pattern	'grid'
?? Bridge Third Skin Density	80
?? Inner Wall Acceleration	700
?? Initial Layer Acceleration	700
?? Compensate Wall Overlaps	True
?? Wipe Retraction Retract Speed	40
?? Mold Angle	40
?? Infill X Offset	0
?? Connect Infill Polygons	False
?? Regular/Maximum Fan Speed Threshold	10
?? Draft Shield Limitation	'full'
?? Steps per Millimeter (E)	1600
?? Initial Layer Travel Acceleration	5000.0
?? Connect Support Lines	False
?? Extensive Stitching	False
?? Walls	0
?? Infill Y Offset	0
?? Raft Top Line Width	0.4
?? Wipe Retraction Speed	40
?? WP Roof Fall Down	2
?? Machine Width	330
?? None	0
?? Nozzle ID	'unknown'
?? Outer Wall Extruder	'-1'
?? Monotonic Ironing Order	False
?? Skin Overlap Percentage	5
?? Retraction Retract Speed	40
?? Support Interface Pattern	'concentric'
?? Small Feature Max Length	0.0
?? Extrusion Cool Down Speed Modifier	0.7
?? None	0
?? Extruder Prime X Position	0
?? Support Interface Linear Advance Factor	0
?? Inner Wall Speed	50
?? Include Material Temperatures	True
?? Prime Tower Acceleration	700
?? Fuzzy Skin Point Distance	0.8
?? None	False
?? No Skin in Z Gaps	False
?? Gradual Infill Step Height	1.5
?? Maximum Model Angle	50
?? Remove All Holes	False
?? Use Towers	True
?? Prime Tower X Position	320.6
?? Crystalline Material	False
?? Skin Removal Width	1.2000000000000002
?? WP Connection Flow	100
?? Equalize Filament Flow	True
?? Inner Wall(s) Flow	99
?? Nozzle Switch Extra Prime Amount	0
?? Nozzle Angle	45
?? Coasting Speed	80
?? Nozzle Switch Retract Speed	20
?? Outer Wall Inset	0
?? Has Heated Build Plate	True
?? Infill Density	20.0
?? Maximum Speed Z	299792458000
?? Wipe Repeat Count	5
?? Support Brim Width	8.0
?? Wipe Move Distance	20
?? Bottom Layers	4
?? Small Hole Max Size	0
?? Enable Ooze Shield	False
?? Top/Bottom Pattern	'lines'
?? Support Speed	35
?? Lift Head	False
?? Ironing Pattern	'zigzag'
?? Skirt/Brim Acceleration	700
?? Dual Extrusion	0
?? None	0
?? Firmware Retraction	False
?? Ooze Shield Distance	2
?? Support Floor Jerk	35
?? Break Up Support In Chunks	False
?? Union Overlapping Volumes	True
?? WP Top Delay	0
?? Maximum Retraction Count	90
?? Adaptive Layers Topography Size	0.2
?? Infill Overlap	0.06
?? Wall Speed	50
?? Y Endstop in Positive Direction	False
?? Retraction Minimum Travel	0.8
?? Bridge Skin Support Threshold	50
?? WP Roof Drag Along	0.8
?? Support Top Distance	0.1
?? Support Stair Step Minimum Slope Angle	10.0
?? Connect Infill Lines	True
?? Enable Support Interface	False
?? Cutting Mesh	False
?? Initial Layer Flow	90
?? Enable Retraction	True
?? WP Flat Delay	0.1
?? Cooling	0
?? Retraction Speed	40
?? Support Interface Thickness	1
?? Enable Draft Shield	False
?? Anti Overhang Mesh	False
?? Outer Nozzle Diameter	1
?? Flow	100
?? Enable Prime Tower	False
?? Enable Conical Support	False
?? Mesh Position Z	0
?? WP Downward Printing Speed	5
?? Show Machine Variants	False
?? Enable Nozzle Temperature Control	True
?? Wall Line Width	0.4
?? Prime Tower Speed	50
?? Cool Down Speed	2.0
?? Support Roof Line Directions	'[ ]'
?? Top/Bottom Thickness	0.8
?? Support Interface Flow	100
?? Support Join Distance	2.0
?? Auto Temperature	False
?? Machine	0
?? Fuzzy Skin Thickness	0.3
?? Raft Smoothing	5
?? Drop Down Support Mesh	True
?? Travel Jerk	30
?? Support Floor Extruder	0
?? Tower Diameter	3.0
?? Overhanging Wall Angle	90
?? Ironing Acceleration	700
?? Minimal Time Standby Temperature	50.0
?? Skirt/Brim Flow	100
?? Support Roof Density	100
?? Gradual Infill Steps	0
?? None	''
?? Default Printing Temperature	245.0
?? WP Roof Outer Delay	0.2
?? None	''
?? Wait for Build Plate Heatup	True
?? Enable Support Floor	False
?? Support Chunk Size	20
?? Has Build Volume Temperature Stabilization	False
?? Skirt/Brim Jerk	35
?? WP Fall Down	0.5
?? Bridge Skin Flow	85
?? Prime Tower Linear Advance Factor	0
?? Support Infill Speed	35
?? Minimum Speed	10
?? Raft Middle Print Jerk	35
?? X Endstop in Positive Direction	False
?? Extra Infill Wall Count	0
?? Steps per Millimeter (Z)	50
?? Bridge Sparse Infill Max Density	10
?? Wipe Pause	0
?? Support Brim Line Count	20
?? Wall Flow	100
?? Skirt/Brim Minimum Length	250
?? Minimum Infill Area	0
?? Raft Base Print Speed	18.75
?? Randomize Infill Start	False
?? WP Strategy	'compensate'
?? Command Line Settings	0
?? Outer Wall Acceleration	700
?? Build Plate Adhesion Type	'brim'
?? Infill Linear Advance Factor	0
?? Support Interface Line Directions	'[ ]'
?? Alternate Extra Wall	False
?? Minimum Polygon Circumference	1.0
?? Mesh Position X	0
?? None	0
?? Gradual Support Infill Steps	0
?? Fan Speed Override	False
?? Retraction Distance	6
?? Top Surface Skin Layers	2
?? Material	0
?? Fill Gaps Between Walls	'everywhere'
?? Outer Wall Speed	40
?? Ooze Shield Angle	60
?? Bridge Second Skin Density	75
?? Build Plate Adhesion	0
?? Scaling Factor Shrinkage Compensation	100.0
?? Top/Bottom Jerk	35
?? Support Floor Density	100
?? Top/Bottom Line Directions	'[ ]'
?? Minimum Support Area	0.0
?? Initial Layer Print Jerk	35
?? Support Infill Layer Thickness	0.2
?? Maximum Deviation	0.025
?? Initial Printing Temperature	230
?? Tree Support Branch Angle	40
?? Support Acceleration	700
?? Number of Extruders	1
?? Heat Up Speed	2.0
?? Print Sequence	'all_at_once'
?? Filter Out Tiny Gaps	True
?? G-code Flavor	'RepRap (RepRap)'
?? End of Filament Purge Length	20
?? Limit Support Retractions	False
?? Default Z Jerk	0.4
?? Mesh Fixes	0
?? Surface Energy	100
?? Maximum Travel Resolution	0.8
?? Support Roof Flow	100
?? Wipe Z Hop	False
?? Number of Slower Layers	2
?? WP Bottom Printing Speed	5
?? Flush Purge Length	60
?? Top Surface Skin Jerk	35
?? Raft Top Print Acceleration	700
?? Support Horizontal Expansion	0
?? Nozzle Switch Prime Speed	20
?? Ironing Flow	0.1
?? Minimum Feedrate	0.0
?? Enable Print Cooling	True
?? Outer Wall Line Width	0.4
?? Skirt/Brim Linear Advance Factor	0
?? Prime Tower Y Position	298.6
?? Infill Travel Optimization	False
?? Retraction Prime Speed	40
?? Always Write Active Tool	False
?? Top Surface Skin Speed	25.0
?? Tree Support Branch Distance	0.7
?? Wipe Retraction Extra Prime Amount	-0.1
?? Z Seam Relative	False
?? Support Linear Advance Factor	0
?? Z Seam Position	'back'
?? Steps per Millimeter (X)	50
?? Support Floor Speed	23.333333333333332
?? Default Build Plate Temperature	80.0
?? Maximum Speed for Flow Equalization	150
?? Skirt Line Count	1
?? Bridge Second Skin Fan Speed	0
?? Top Surface Skin Line Width	0.4
?? None	False
?? Initial Layer Travel Jerk	30.0
?? Inner Wall(s) Line Width	0.4
?? Wall Thickness	0.8
?? Anti-ooze Retracted Position	-4
?? Enable Jerk Control	True
?? Infill Support	False
?? Support Extruder	0
?? Outer Before Inner Walls	False
?? Relative Extrusion	True
?? Overhanging Wall Speed	100
?? Bridge Wall Coasting	80
?? Infill Overlap Percentage	15
?? Bottom Skin Expand Distance	1.2000000000000002
?? Is Center Origin	False
?? Infill Flow	100
?? Prime Tower Brim	False
?? Conical Support Minimum Width	5.0
?? Infill	0
?? First Layer Support Extruder	0
?? Initial Layer Z Overlap	0.15
?? Support Floor Horizontal Expansion	0.0
?? Wall Acceleration	700
?? Z Seam Y	330
?? Bottom Thickness	0.8
?? Nozzle Switch Retraction Speed	20
?? Center Object	False
?? Outer Wall Linear Advance Factor	0
?? Nozzle Switch Retraction Distance	16
?? Bottom Pattern Initial Layer	'lines'
?? Top Layers	6
?? None	0
?? WP Knot Size	0.6
?? Z Hop Speed	10
?? Top Surface Skin Acceleration	700
?? Travel Acceleration	5000
?? Maximum Park Duration	300
?? Number of Extruders That Are Enabled	1
?? Bridge Second Skin Flow	100
?? Top/Bottom Line Width	0.4
?? Alternate Mesh Removal	True
?? Print Jerk	35
?? Tree Support Branch Diameter	1
?? Printing Temperature	230
?? Support Floor Line Distance	0.4
?? Travel Speed	300
?? Wall Jerk	35
?? Initial Layer Horizontal Expansion	0
?? Support Jerk	35
?? Build Plate Temperature	85
?? End G-code	'M104 S0\nM140 S0\n;Retract the filament\nG92 E1\nG1 E-1 F300\nG28 X0 Y0\nM84'
?? Print Thin Walls	True
?? Final Printing Temperature	225
?? Raft Fan Speed	0
?? Support Roof Thickness	1
?? Top Surface Skin Flow	100
?? Infill Wipe Distance	0.4
?? Raft Top Layer Thickness	0.2
?? Minimum Skin Width for Expansion	7.34788079488412e-17
?? Coasting Volume	0.2
?? Raft Base Line Spacing	1.6
?? Break Preparation Retracted Position	-16
?? Raft Print Speed	25.0
?? Travel Avoid Distance	0.625
?? Support Interface Horizontal Expansion	0.0
?? Support Line Width	0.4
?? Cross 3D Pocket Size	4.0
?? Initial Layer Jerk	35
?? Tower Roof Angle	65
?? Combing Mode	'all'
?? Maximum Acceleration Z	100
?? Initial Layer Support Line Distance	2.6666666666666665
?? Maximum Overhang Hole Area	0
?? Top Surface Skin Extruder	'-1'
?? Initial Fan Speed	0
?? Support Chunk Line Count	8
?? Infill Layer Thickness	0.2
?? Infill Speed	40
?? Wall Extruder	'-1'
?? Layer Start Y	0.0
?? Z Seam X	165.0
?? Machine Type	'Unknown'
?? Support Floor Acceleration	700
?? Machine Head & Fan Polygon	[[-20, 10], [10, 10], [10, -10], [-20, -10]]
?? Default Filament Jerk	5.0
?? Maximum Skin Angle for Expansion	90
?? Raft Base Fan Speed	0
?? Support Roof Extruder	0
?? WP Flow	100
?? Avoid Supports When Traveling	True
?? Flow Rate Compensation Max Extrusion Offset	0
?? Small Feature Initial Layer Speed	50
?? Feeder Wheel Diameter	10.0
?? Adaptive Layers Maximum Variation	0.1
?? Initial Layer Height	0.2
?? Support Density	15
?? Line Width	0.4
?? Wipe Retraction Prime Speed	40
?? Flush Purge Speed	0.5
?? Infill Overhang Angle	40
?? Mesh Position Y	0
?? Bridge Skin Density	100
?? Top Skin Removal Width	1.2000000000000002
?? Nozzle Disallowed Areas	[]
?? Prime Tower Flow	100
?? Support Interface Speed	23.333333333333332
?? Enable Bridge Settings	True
?? Regular Fan Speed at Layer	2
?? Wipe Retraction Distance	6
?? Include Build Plate Temperature	True
?? Iron Only Highest Layer	False
?? Tree Support Collision Resolution	0.2
?? Gradual Support Infill Step Height	1
?? Start G-code	'G28 ;Home\nG1 Z15.0 F6000 ;Move the platform down 15mm\n;Prime the extruder\nG92 E0\nG1 F200 E3\nG92 E0'
?? Prefer Retract	False
?? Fuzzy Skin Density	1.25
?? Maximum Speed X	299792458000
?? Hole Horizontal Expansion	0
?? Support Floor Flow	100
?? Minimum Extrusion Distance Window	6
?? Support Line Distance	2.6666666666666665
?? Max Comb Distance With No Retract	0
?? Raft Middle Thickness	0.30000000000000004
?? Initial Layer Line Width	100.0
?? Enable Acceleration Control	True
?? Wall Linear Advance Factor	0
?? Outer Wall Flow	98
?? Raft Print Jerk	35
?? Initial Layer Travel Speed	250
?? Maximum Acceleration X	9000
?? Shared Nozzle Initial Retraction	0
?? Break Temperature	50
?? Prime Tower Line Width	0.4
?? Raft Print Acceleration	700
?? Remove Empty First Layers	True
?? Build Volume Temperature	0
?? Top Skin Expand Distance	1.2000000000000002
?? Support Stair Step Maximum Width	5.0
?? Enable Support Roof	False
?? Z Endstop in Positive Direction	True
?? Top Thickness	0.8
?? Skirt/Brim Line Width	0.4
?? Nozzle Length	3
?? None	0
?? Heat Zone Length	16
?? Remove Mesh Intersection	False
?? Top/Bottom Skin Linear Advance Factor	0
?? Conical Support Angle	30
?? Support Distance Priority	'z_overrides_xy'
?? Support X/Y Distance	0.7
?? Maximum Fan Speed	85
?? Z Hop After Extruder Switch Height	2
?? Extruder Prime Z Position	0
?? Support Flow	100
?? Ironing Inset	0.39980000000000004
?? Raft Middle Print Acceleration	700
?? Support Infill Jerk	35
?? Small Feature Speed	50
?? Break Retracted Position	-50
?? Surface Mode	'normal'
?? Extruder Prime Y Position	0
?? Skirt Distance	3
?? Cross Infill Density Image	''
?? Draft Shield Height	10
?? Skirt/Brim Speed	15
?? Infill Mesh	False
?? Raft Base Line Width	0.8
?? Maximum Tower-Supported Diameter	3.0
?? Wipe Inactive Nozzle on Prime Tower	True
?? Minimum Layer Time	10
Containers
Container: custom_extruder_1 #2_user
type	user
id	custom_extruder_1 #2_user
name	custom_extruder_1 #2_user
definition	custom
Container: Brad's PETG
type	quality_changes
id	custom_extruder_1_#2_brad's_petg
name	Brad's PETG
definition	fdmprinter
quality_type	draft
?? Wall Speed	50
?? Outer Wall Speed	40
?? Print Acceleration	700
?? Retraction Prime Speed	=retraction_speed
?? Enable Ironing	True
?? Infill Speed	40
?? Tree Support Branch Distance	0.7
?? Fan Speed	55
?? Equalize Filament Flow	True
?? Maximum Fan Speed	85
?? Bridge Wall Speed	17
?? Inner Wall(s) Flow	99
?? Bridge Skin Flow	85
?? Coasting Speed	80
?? Bridge Has Multiple Layers	False
?? Print Jerk	35
?? Regular Fan Speed	75
?? Tree Support Branch Diameter	1
?? Printing Temperature	230
?? Connect Infill Lines	True
?? Travel Speed	300
?? Initial Layer Flow	90
?? Infill Density	20.0
?? Wall Line Count	3
?? Seam Corner Preference	'z_seam_corner_any'
?? Retraction Speed	40
?? Print Thin Walls	True
?? Final Printing Temperature	225
?? Initial Printing Temperature	230
?? Bridge Sparse Infill Max Density	10
?? Support Overhang Angle	35
?? Outer Wall Flow	98
?? Top Surface Skin Flow	100
?? Infill Wipe Distance	0.4
?? Retract at Layer Change	True
?? Coasting Volume	0.2
?? Print Speed	50
?? Bridge Wall Flow	85
?? Retraction Extra Prime Amount	-0.1
?? Z Hop Height	2
?? Initial Layer Travel Speed	250
?? Bridge Wall Coasting	80
?? Support Speed	35
?? Infill Overlap Percentage	15
?? Support Wall Line Count	1
?? Avoid Supports When Traveling	True
?? Infill Flow	100
?? Limit Support Retractions	False
?? Initial Layer Speed	15
?? Inner Wall Speed	50
?? Monotonic Top/Bottom Order	True
?? Optimize Wall Printing Order	True
?? Bridge Fan Speed	90
?? Retraction Distance	6
?? Ironing Flow	0.1
?? Minimum Layer Time	10
?? Top Surface Skin Layers	2
?? Top Layers	6