22/10/2021, 21:25:45: Connected to 192.168.1.5
22/10/2021, 21:26:32: Connection interrupted, attempting to reconnect...: HTTP request timed out
22/10/2021, 21:26:35: Connection established
22/10/2021, 21:26:43: Connection interrupted, attempting to reconnect...: HTTP request timed out
22/10/2021, 21:26:44: Connection established
22/10/2021, 21:26:53: Connection interrupted, attempting to reconnect...: HTTP request timed out
22/10/2021, 21:27:02: Connection established
22/10/2021, 21:27:12: Connection interrupted, attempting to reconnect...: HTTP request timed out
22/10/2021, 21:27:12: Connection established
22/10/2021, 21:27:21: Connection interrupted, attempting to reconnect...: HTTP request timed out
22/10/2021, 21:29:10: Connection established
22/10/2021, 21:29:19: Connection interrupted, attempting to reconnect...: HTTP request timed out
22/10/2021, 21:29:42: Connection established
22/10/2021, 21:29:50: Connection interrupted, attempting to reconnect...: HTTP request timed out
22/10/2021, 21:30:14: Connection established
22/10/2021, 21:30:22: Connection interrupted, attempting to reconnect...: HTTP request timed out
22/10/2021, 21:30:25: Connection established
22/10/2021, 21:33:26: M122: === Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.3 (2021-06-15 21:46:11) running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: GRMFB-Y396U-D65J0-40KM8-0L03Z-HS72X
Used output buffers: 3 of 40 (40 max)
=== RTOS ===
Static ram: 102724
Dynamic ram: 106560 of which 312 recycled
Never used RAM 31252, free system stack 120 words
Tasks: NETWORK(ready,16.7%,202) HEAT(delaying,0.0%,344) Move(notifyWait,0.3%,284) CanReceiv(notifyWait,0.0%,941) CanSender(notifyWait,0.0%,357) CanClock(delaying,0.0%,332) TMC(notifyWait,1.2%,114) MAIN(running,80.8%,412) IDLE(ready,0.1%,29) AIN(delaying,0.9%,264), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 02:54:41 ago, cause: software
Last software reset at 2021-10-22 18:38, reason: User, GCodes spinning, available RAM 34676, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x04
Aux0 errors 0,0,0
MCU revision 3, ADC conversions started 10482183, completed 10482182, timed out 0, errs 0
Step timer max interval 723
MCU temperature: min 38.1, current 40.2, max 40.4
Supply voltage: min 23.8, current 23.9, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/16/16, gc cycles 0
Driver 0: position 22225, ok, SG min/max 0/20, read errors 0, write errors 0, ifcnt 68, reads 59063, writes 0, timeouts 0, DMA errors 0
Driver 1: position 3242, ok, SG min/max 0/16, read errors 0, write errors 0, ifcnt 68, reads 59063, writes 0, timeouts 0, DMA errors 0
Driver 2: position 615, ok, SG min/max 0/16, read errors 0, write errors 0, ifcnt 68, reads 59063, writes 0, timeouts 0, DMA errors 0
Driver 3: position 0, ok, SG min/max 0/66, read errors 0, write errors 0, ifcnt 65, reads 59063, writes 0, timeouts 0, DMA errors 0
Driver 4: position 0, standstill, SG min/max 0/66, read errors 0, write errors 0, ifcnt 66, reads 59063, writes 0, timeouts 0, DMA errors 0
Driver 5: position 0, ok, SG min/max 0/44, read errors 0, write errors 0, ifcnt 64, reads 59063, writes 0, timeouts 0, DMA errors 0
Driver 6: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 59, reads 59064, writes 0, timeouts 0, DMA errors 0
Date/time: 2021-10-22 21:33:25
Cache data hit count 4294967295
Slowest loop: 26.39ms; fastest: 0.10ms
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 3.8ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 7143, completed moves 7112, hiccups 0, stepErrors 0, LaErrores 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 7143, completed moves 7112, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state 3
=== AuxDDARing ===
Schedu = 0 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.1
Heater 1 is on, I-accum = 0.8
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is doing "G1 X113.587 Y157.32 E3.16237" in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 5847, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 17 (min 17), ts 3248/0/0
Tx timeouts 0,0,3248,0,0,2599 last cancelled message type 4514 dest 127

=== Network ===
Slowest loop: 199.96ms; fastest: 0.06ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 2 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 12
WiFi firmware version 1.26
WiFi MAC address f0:08:d1:02:b5:80
WiFi Vcc 3.41, reset reason Power up
WiFi flash size 2097152, free heap 23880
WiFi IP address 192.168.1.5
WiFi signal strength -46dBm, mode 802.11n, reconnections 0, sleep mo
22/10/2021, 21:36:19: M98 P"config.g" : Cancelled printing file 0:/gcodes/Quasar Compartment_0.2mm_PLA_VCORE3_2h46m.gcode, print time was 0h 21m
Error: G0/G1: insufficient axes homed
Warning: the height map was loaded when the current Z=0 datum was not determined probing. This may result in a height offset.
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 445C
Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 572C
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 445C