4.11.2021, 07:49:46	M122
4.11.2021, 07:48:44	Connected to 192.168.100.20
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-9P63L-DJ3T8-6J1DD-3SD6S-9V4V8
Used output buffers: 1 of 40 (21 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 92620 of which 240 recycled
Never used RAM 110428, free system stack 206 words
Tasks: NETWORK(ready,29.5%,230) ETHERNET(notifyWait,0.2%,117) HEAT(delaying,0.0%,331) Move(notifyWait,0.0%,352) CanReceiv(notifyWait,0.0%,908) CanSender(notifyWait,0.0%,374) CanClock(delaying,0.0%,351) TMC(notifyWait,7.6%,93) MAIN(running,62.5%,924) IDLE(ready,0.2%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:01:16 ago, cause: software
Last software reset at 2021-11-04 07:48, reason: User, GCodes spinning, available RAM 107572, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,1
Step timer max interval 129
MCU temperature: min 41.5, current 43.5, max 43.9
Supply voltage: min 21.8, current 21.9, max 21.9, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.2, max 12.3, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, reads 32593, writes 14 timeouts 0, SG min/max 0/0
Driver 1: position 0, standstill, reads 32596, writes 11 timeouts 0, SG min/max 0/0
Driver 2: position 0, standstill, reads 32593, writes 14 timeouts 0, SG min/max 0/0
Driver 3: position 0, standstill, reads 32594, writes 14 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 32594, writes 14 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 32597, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2021-11-04 07:49:44
Slowest loop: 5.23ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 0.5ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = 2 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 694, received 5, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 320, free buffers 49 (min 49), ts 383/382/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 10.96ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 2 2 2 2 0 0 0
4.11.2021, 08:01:15	M401
4.11.2021, 08:01:59	M402
4.11.2021, 08:06:10	Upload of config.g successful after 0s
4.11.2021, 08:06:21	Connection interrupted, attempting to reconnect...
HTTP request timed out
4.11.2021, 08:06:22	Connection established
4.11.2021, 08:06:36	G28
Warning: motor phase A may be disconnected reported by driver(s) 2
Warning: motor phase B may be disconnected reported by driver(s) 2
4.11.2021, 08:06:38	Error: Probe already triggered at start of probing move
4.11.2021, 08:06:40	Error: Probe already triggered at start of probing move
Error: Probe already triggered at start of probing move
4.11.2021, 08:07:36	Upload of config.g successful after 0s
4.11.2021, 08:07:47	Connection interrupted, attempting to reconnect...
HTTP request timed out
4.11.2021, 08:07:48	Connection established
4.11.2021, 08:08:01	G28
Warning: motor phase A may be disconnected reported by driver(s) 2
Warning: motor phase B may be disconnected reported by driver(s) 2
4.11.2021, 08:08:17	Emergency stop, attemping to reconnect...
4.11.2021, 08:09:19	Connection interrupted, attempting to reconnect...
4.11.2021, 08:09:25	Connection established
4.11.2021, 08:10:10	M401