; Configuration file for Flu Super8 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.0-LPC-STM32+08 on Sun Nov 21 2021 14:17:20 GMT+0100 (hora estándar de Europa central)

; General preferences
G90                                                                     ; send absolute coordinates...
M83                                                                     ; ...but relative extruder moves
M550 P"machine"                                                         ; set printer name
M302 P1

; Network
M552 S1                                                                 ; enable network
M586 P0 S1                                                              ; enable HTTP
M586 P1 S0                                                              ; disable FTP
M586 P2 S0                                                              ; disable Telnet

; Drives
M569 P0 S0 D3 H50 v50
                                                                        ; physical drive 0 goes forwards using default driver timings
M569 P1 S0 D3 H50 V50
                                                                        ; physical drive 1 goes forwards using default driver timings
M569 P2 S1 D3                                                           ; physical drive 2 goes forwards using default driver timings
M569 P3 S1                                                              ; physical drive 3 goes forwards using default driver timings
M569 P4 S1                                                              ; physical drive 4 goes forwards using default driver timings
M569 P5 S1                                                              ; physical drive 5 goes forwards using default driver timings
M569 P6 S1                                                              ; physical drive 6 goes forwards using default driver timings
M569 P7 S1                                                              ; physical drive 7 goes forwards using default driver timings
M584 X0 Y1 Z2 E3:4:5:6:7                                                ; set drive mapping
M350 X256 Y256 Z16 E16:16:16:16:16 I1                                     ; configure microstepping with interpolation
M92 X6400 Y6400 Z533,33 E145:420.00:420.00:420.00:420.00               ; set steps per mm
M566 X300 Y300 Z500 E900:120.00:120.00:120.00:120.00            ; set maximum instantaneous speed changes (mm/min)
M203 X1000 Y1000 Z1500 E3000:1200.00:1200.00:1200.00:1200.00       ; set maximum speeds (mm/min)
M201 X200 Y200 Z250 E500:250.00:250.00:250.00:250.00            ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800:800:800:800:800 I30                          ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                                                 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                                        ; set axis minima
M208 X230 Y210 Z35 S0                                                  ; set axis maxima

; Endstops
M574 X1 S1 P"!io0" 
M574 Y1 S1 P"!io1"
M574 Z2 S1 P"!io2"                                                      ; configure active-high endstop for low end on Z via pin io2

; Z-Probe
M558 P0 H5 F120 T6000                                                   ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                                                ; define mesh grid

; Heaters
M308 S0 P"ADC_0" Y"thermistor" T100000 B4092                            ; configure sensor 0 as thermistor on pin ADC_0
M950 H0 C"bed" T0                                                       ; create bed heater output on bed and map it to sensor 0
M307 H0 B1 S1.00                                                        ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                                 ; map heated bed to heater 0
M143 H0 S120                                                            ; set temperature limit for heater 0 to 120C
M143 H0 S120                                                            ; set temperature limit for heater 0 to 120C
M308 S1 P"ADC_1" Y"thermistor" T10000 B3988                             ; configure sensor 1 as thermistor on pin ADC_1
M950 H1 C"heat0" T1                                                     ; create nozzle heater output on heat0 and map it to sensor 1
M307 H1 B0 S1.00 I1                                                     ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                                            ; set temperature limit for heater 1 to 280C
                                                                        ; set temperature limit for heater 4 to 280C

; Fans
M950 F0 C"fan0" Q500                                                    ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H T1999                                                      ; set fan 0 value. Thermostatic control is turned off

M950 F1 C"fan1" Q500                                                    ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H T1999 

; Tools
M563 P1 S"tool1" D0 H1 F0                                               ; define tool 1
G10 P1 X0 Y0 Z0                                                         ; set tool 1 axis offsets
G10 P1 R0 S0                                                            ; set initial tool 1 active and standby temperatures to 0C
                                                                        ; set initial tool 3 active and standby temperatures to 0C

; Custom settings are not defined