20:23:46: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 107, measured sensitivity 25.11mm/rev, min 9% max 205% over 88393.8mm
20:21:03: : Finished printing file 0:/gcodes/3D print with template LOWER LEFT DOOR.gcode, print time was 59h 8m
20:21:02: : Finished printing file 0:/gcodes/3D print with template LOWER LEFT DOOR.gcode, print time was 59h 8m
16:25:56: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.08mm/rev, min 17% max 102% over 8307.1mm
16:21:57: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.12mm/rev, min 17% max 102% over 6975.3mm
16:20:21: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.09mm/rev, min 17% max 102% over 6180.9mm
16:18:44: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 130 agc 106, measured sensitivity 25.12mm/rev, min 17% max 102% over 5696.6mm
16:16:26: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.15mm/rev, min 17% max 102% over 5308.0mm
16:15:38: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.17mm/rev, min 17% max 102% over 4952.1mm
16:13:20: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.14mm/rev, min 17% max 102% over 3736.0mm
16:11:46: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.17mm/rev, min 17% max 102% over 3238.8mm
16:10:50: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.21mm/rev, min 17% max 102% over 2983.0mm
16:08:42: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.27mm/rev, min 17% max 103% over 2656.0mm
16:06:11: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.45mm/rev, min 17% max 103% over 1421.0mm
16:05:41: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.37mm/rev, min 17% max 103% over 1140.4mm
16:05:20: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.46mm/rev, min 17% max 103% over 933.4mm
16:05:07: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.52mm/rev, min 17% max 104% over 823.8mm
16:04:51: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.62mm/rev, min 17% max 104% over 726.9mm
16:04:25: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.49mm/rev, min 17% max 104% over 642.3mm
16:04:16: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.54mm/rev, min 17% max 104% over 605.7mm
16:03:48: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.75mm/rev, min 17% max 105% over 472.4mm
16:03:41: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 25.80mm/rev, min 17% max 105% over 448.2mm
16:03:02: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 106, measured sensitivity 24.83mm/rev, min 97% max 101% over 266.9mm
16:02:20: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 106, measured sensitivity 24.78mm/rev, min 100% max 101% over 85.3mm
16:01:49: M24: Printing resumed
16:01:13: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 106, measured sensitivity 28.31mm/rev, min 1% max 115% over 175.4mm
16:01:10: : Printing paused at X137.1 Y252.6 Z388.0
16:01:02: : Resume state saved
16:00:55: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 24.80mm/rev, min 99% max 101% over 109.8mm
16:00:53: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 24.80mm/rev, min 99% max 101% over 109.8mm
16:00:52: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 24.76mm/rev, min 99% max 101% over 97.5mm
16:00:51: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 24.77mm/rev, min 99% max 101% over 84.8mm
16:00:50: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 24.72mm/rev, min 99% max 101% over 72.6mm
16:00:39: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 24.69mm/rev, min 99% max 101% over 48.2mm
16:00:25: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 24.62mm/rev, min 100% max 100% over 24.1mm
16:00:20: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, no calibration data
16:00:18: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, no calibration data
16:00:16: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, no calibration data
16:00:07: M24: Printing resumed
15:59:43: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 43.08mm/rev, min -1% max 174% over 66.5mm
15:59:29: : Printing paused at X507.3 Y305.6 Z388.0
15:59:17: : Resume state saved
15:59:08: M24: Printing resumed
15:58:54: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 14666.23mm/rev, min 100% max 100% over 28.6mm
10:28:00: M120M83G1 E100 F1800M121
10:27:54: M120M83G1 E100 F1800M121
10:27:46: M120M83G1 E100 F1800M121
10:27:17: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 106, measured sensitivity 14666.23mm/rev, min 100% max 100% over 28.6mm
10:25:03: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 106, measured sensitivity 14666.23mm/rev, min 100% max 100% over 28.6mm
10:24:49: : Printing paused at X317.8 Y313.9 Z388.0
10:24:40: : Resume state saved
10:24:35: M24: Printing resumed
10:24:06: M120M83G1 E100 F1800M121
10:24:00: M120M83G1 E100 F1800M121
10:22:38: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 105, measured sensitivity 2283.93mm/rev, min 100% max 100% over 31.2mm
10:22:35: : Printing paused at X637.7 Y304.5 Z388.0
10:22:23: : Resume state saved
10:22:19: M24: Printing resumed
10:21:32: M120M83G1 E100 F1800M121
10:21:18: M120M83G1 E100 F1800M121
10:21:11: M120M83G1 E100 F1800M121
10:21:05: M120M83G1 E100 F1800M121
10:20:59: M120M83G1 E100 F1800M121
10:20:53: M120M83G1 E100 F1800M121
10:20:47: M120M83G1 E100 F1800M121
10:20:41: M120M83G1 E100 F1800M121
10:20:36: M120M83G1 E100 F1800M121
10:20:25: M120M83G1 E100 F3600M121
10:20:19: M120M83G1 E100 F3600M121
10:20:13: M120M83G1 E100 F3600M121
10:20:03: M120M83G1 E100 F1800M121
10:19:56: M120M83G1 E100 F1800M121
10:19:50: M120M83G1 E100 F1800M121
10:19:42: M120M83G1 E100 F1800M121
10:19:36: M120M83G1 E100 F1800M121
10:19:30: M120M83G1 E100 F1800M121
10:19:24: M120M83G1 E100 F1800M121
10:18:41: M591 D0: Printing paused at X843.5 Y188.8 Z388.0Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 105, measured sensitivity 37091.11mm/rev, min 100% max 100% over 36.2mm
10:18:27: : Resume state saved
10:18:22: M24: Printing resumed
10:17:41: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 105, measured sensitivity 44.35mm/rev, min -1% max 178% over 92.3mm
10:17:26: M120M83G1 E100 F1800M121
10:17:19: M120M83G1 E100 F1800M121
10:17:13: M120M83G1 E100 F1800M121
10:17:08: M120M83G1 E100 F1800M121
10:17:00: M120M83G1 E100 F1800M121
10:16:52: M120M83G1 E100 F1800M121
10:16:41: M120M83G1 E100 F1800M121
10:16:37: M120M83G1 E100 F1800M121
10:16:30: M120M83G1 E100 F1800M121
10:16:25: M120M83G1 E100 F1800M121
10:16:19: M120M83G1 E100 F1800M121
10:16:13: M120M83G1 E100 F1800M121
10:16:06: M120M83G1 E100 F1800M121
10:16:00: M120M83G1 E100 F1800M121
10:15:33: M591 D0: Printing paused at X1124.5 Y159.8 Z388.0Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 105, measured sensitivity 44.35mm/rev, min -1% max 178% over 92.3mm
10:15:16: : Resume state saved
10:15:05: M24: Printing resumed
10:12:46: : Printing paused at X601.3 Y250.3 Z388.0
10:12:34: : Resume state saved
10:12:32: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 105, measured sensitivity 10001.01mm/rev, min 100% max 100% over 29.3mm
10:12:30: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 105, measured sensitivity 10001.01mm/rev, min 100% max 100% over 29.3mm
10:12:30: M591 D0: Error: M24: Cannot print, because no file is selected!Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 105, measured sensitivity 10001.01mm/rev, min 100% max 100% over 29.3mm
10:11:42: M120M83G1 E100 F1800M121
10:11:36: M120M83G1 E100 F1800M121
10:11:31: M120M83G1 E100 F1800M121
10:11:16: M120M83G1 E100 F1800M121
10:11:14: M120M83G1 E100 F1800M121
10:11:12: M120M83G1 E100 F1800M121
10:11:09: M120M83G1 E100 F1800M121
10:10:59: : Printing paused at X293.1 Y250.3 Z388.0
10:10:50: : Resume state saved
10:10:21: M120M83G1 E100 F1800M121
10:10:11: M120M83G1 E100 F1800M121
10:09:35: M120M83G1 E-100 F1800M121
10:04:14: : Printing paused at X66.0 Y238.6 Z388.0
10:04:08: : Resume state saved
10:03:02: : Printing resumed
08:49:50: : Printing paused at X834.6 Y184.6 Z388.0
08:49:38: : Resume state saved
23:13:23: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 107, measured sensitivity 24.90mm/rev, min 22% max 196% over 188428.1mm
14:28:43: M24: Printing resumed
14:26:59: M120M83G1 E100 F1800M121
14:26:54: M120M83G1 E100 F1800M121
14:26:52: M120M83G1 E100 F1800M121
14:26:44: M120M83G1 E50 F1800M121
14:26:26: M120M83G1 E50 F1800M121
14:24:52: M120M83G1 E-50 F1800M121
14:20:56: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 105, measured sensitivity 24.87mm/rev, min 85% max 102% over 66250.5mm
08:56:25: : Printing paused at X796.7 Y307.3 Z294.0
08:56:12: : Resume state saved
05:30:14: : Printing resumed
05:19:58: : Printing paused at X133.6 Y238.4 Z266.0
05:19:51: : Resume state saved
00:43:43: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 24.89mm/rev, min 33% max 186% over 566133.8mm
16:30:56: Connection established!
16:30:54: Disconnected.
15:44:53: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 24.91mm/rev, min 33% max 186% over 393356.2mm
12:06:02: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 130 agc 106, measured sensitivity 24.92mm/rev, min 33% max 170% over 324214.1mm
05:30:17: Connection established!
05:30:17: Disconnected.
05:21:18: Connection established!
05:21:17: Disconnected.
00:03:01: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 130 agc 108, measured sensitivity 25.05mm/rev, min 61% max 102% over 100003.7mm
20:45:44: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 129 agc 105, measured sensitivity 24.88mm/rev, min 98% max 101% over 11806.5mm
20:26:05: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 130 agc 105, measured sensitivity 24.85mm/rev, min 99% max 101% over 2345.1mm
20:22:34: M290 S-0.05
20:22:32: M290 S0.05
20:22:29: M290 S-0.05
20:21:33: M290 S-0.05
20:21:30: M290 S0.05
20:21:14: M290 S0.05
20:21:14: M290 S0.05
20:21:13: M290 S0.05
20:21:12: M290 S0.05
20:20:29: M32 ""3D print with template LOWER LEFT DOOR.gcode"": File 3D print with template LOWER LEFT DOOR.gcode selected for printing
20:19:51: T0
19:18:40: G28
19:14:25: Connection established!
19:14:12: G28: Emergency Stop! Reset the controller to continue.
19:09:00: T0
19:08:58: G10 P0 S235
19:08:43: Connection established!
18:37:54: Disconnected.
18:36:15: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 106, measured sensitivity 24.80mm/rev, min 98% max 103% over 43624.9mm
18:34:36: : Finished printing file 0:/gcodes/3D print with template UPPER LEFT REAR.gcode, print time was 19h 2m
16:14:55: : Printing resumed
15:57:23: : Printing paused at X174.6 Y322.0 Z494.0
15:57:17: : Resume state saved
10:44:36: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 129 agc 104, measured sensitivity 24.91mm/rev, min 37% max 183% over 235108.5mm
01:50:11: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 129 agc 105, measured sensitivity 25.04mm/rev, min 37% max 179% over 59492.0mm
00:53:32: G10 P0 S245
00:45:49: G10 P0 S255
00:44:14: G10 P0 S210
00:40:35: G10 P0 S215
00:35:16: G10 P0 S220
00:25:09: G10 P0 S225
00:15:58: G10 P0 S230
00:10:36: G10 P0 S235
00:05:38: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 129 agc 105, measured sensitivity 25.12mm/rev, min 96% max 102% over 25609.0mm
23:42:12: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 130 agc 105, measured sensitivity 25.02mm/rev, min 98% max 102% over 12556.3mm
23:37:27: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 130 agc 105, measured sensitivity 25.02mm/rev, min 98% max 102% over 10664.0mm
23:20:32: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 105, measured sensitivity 24.80mm/rev, min 99% max 101% over 1381.6mm
23:17:38: M290 S0.05
23:17:38: M290 S0.05
23:17:37: M290 S0.05
23:17:37: M290 S0.05
23:17:37: M290 S0.05
23:15:21: M32 ""3D print with template UPPER LEFT REAR.gcode"": File 3D print with template UPPER LEFT REAR.gcode selected for printing
22:53:43: G28
22:50:30: Connection established!
22:50:30: Page Load complete!