18:37:43: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 96, measured sensitivity 74.60mm/rev, min 0% max 162% over 54.2mm
18:37:28: : Printing paused at X27.8 Y330.6 Z0.4
18:37:20: : Resume state saved
18:37:14: M24: Printing resumed
18:36:57: : Printing paused at X478.0 Y348.1 Z0.4
18:36:46: : Resume state saved
18:36:41: M24: Printing resumed
18:36:15: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 96, measured sensitivity 49.68mm/rev, min 2% max 192% over 56.0mm
18:36:10: M290 S0.05
18:36:09: M290 S0.05
18:36:09: M290 S0.05
18:36:01: : Printing paused at X880.0 Y342.6 Z0.4
18:35:47: : Resume state saved
18:35:41: M24: Printing resumed
18:34:51: G10 P0 S220
18:34:30: : Printing paused at X1051.0 Y275.8 Z0.4
18:34:16: : Resume state saved
18:34:06: M24: Printing resumed
18:33:28: : Printing paused at X513.8 Y275.8 Z0.4
18:33:17: : Resume state saved
18:33:10: M24: Printing resumed
18:33:00: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 96, measured sensitivity 3138.66mm/rev, min 100% max 100% over 36.8mm
18:32:53: : Printing paused at X27.5 Y245.5 Z0.4
18:32:49: : Resume state saved
18:32:45: M24: Printing resumed
18:32:12: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 96, measured sensitivity 36.52mm/rev, min 0% max 146% over 109.0mm
18:32:05: : Printing paused at X159.7 Y338.6 Z0.4
18:31:58: : Resume state saved
18:31:46: M24: Printing resumed
18:31:08: M591 D0: Printing paused at X838.7 Y345.2 Z0.4Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 98, measured sensitivity 1063.62mm/rev, min 100% max 100% over 43.6mm
18:30:53: : Resume state saved
18:30:48: M24: Printing resumed
18:30:16: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 98, measured sensitivity infmm/rev, min 0% max 0% over 39.7mm
18:30:10: : Printing paused at X1109.6 Y248.3 Z0.4
18:29:54: : Resume state saved
18:29:49: M24: Printing resumed
18:29:26: M591 D0: Printing paused at X811.7 Y274.7 Z0.4Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 98, measured sensitivity 3140.31mm/rev, min 100% max 100% over 30.7mm
18:29:13: : Resume state saved
18:29:06: M24: Printing resumed
18:28:44: : Printing paused at X335.1 Y274.7 Z0.4
18:28:35: : Resume state saved
18:28:29: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 98, measured sensitivity infmm/rev, min 0% max 0% over 40.7mm
18:27:45: M32 ""3D print with template UPPE REAR.gcode"": File 3D print with template UPPE REAR.gcode selected for printing
18:27:30: M0 H1: Cancelled printing file 0:/gcodes/3D print with template UPPE REAR.gcode, print time was 0h 1m
18:27:18: M120M83G1 E50 F900M121
18:26:38: M120M83G1 E100 F900M121
18:26:09: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 0 agc 0, error 6
18:26:08: : Printing paused at X838.7 Y345.2 Z0.4
18:25:56: M24: Printing resumedResume state saved
18:25:22: M120M83G1 E100 F900M121
18:24:37: M120M83G1 E100 F900M121
18:24:31: M120G91G1 Z5 F6000M121
18:24:29: M120G91G1 Z5 F6000M121
18:24:28: M120G91G1 Z0.5 F6000M121
18:24:28: M120G91G1 Z0.5 F6000M121
18:24:27: M120G91G1 Z0.5 F6000M121
18:24:27: M120G91G1 Z0.5 F6000M121
18:24:00: M591 D0: Printing paused at X838.7 Y345.2 Z0.4Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 98, measured sensitivity infmm/rev, min 0% max 0% over 40.7mm
18:23:46: : Resume state saved
18:23:41: M24: Printing resumed
18:23:05: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 98, measured sensitivity infmm/rev, min 0% max 0% over 47.0mm
18:22:57: : Printing paused at X1109.6 Y248.3 Z0.4
18:22:42: : Resume state saved
18:22:37: M290 S0.05: Printing resumed
18:21:49: M591 D0: Printing paused at X871.3 Y274.7 Z0.4Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 98, measured sensitivity infmm/rev, min 0% max 0% over 28.3mm
18:21:36: : Resume state saved
18:21:29: M290 S0.05: Printing resumed
18:21:12: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 98, measured sensitivity infmm/rev, min 0% max 0% over 48.1mm
18:21:00: : Printing paused at X394.7 Y274.7 Z0.4
18:20:51: : Resume state saved
18:20:48: M290 S0.05
18:20:47: M290 S0.05
18:20:46: M290 S0.05
18:20:46: M290 S0.05
18:20:46: M290 S0.05
18:19:55: M32 ""3D print with template UPPE REAR.gcode"": File 3D print with template UPPE REAR.gcode selected for printing
18:19:45: G28
18:19:03: M120M83G1 E10 F300M121
18:18:59: M120M83G1 E10 F300M121
18:18:56: M120M83G1 E10 F300M121
18:17:03: Connection established!
18:04:28: Disconnected.
18:03:04: M120M83G1 E-10 F300M121
18:03:03: M120M83G1 E-10 F300M121
18:03:01: M120M83G1 E-10 F300M121
18:02:59: M120M83G1 E-10 F300M121
18:02:58: M120M83G1 E-10 F300M121
18:02:58: M120M83G1 E-10 F300M121
18:02:57: M120M83G1 E-10 F300M121
18:02:57: M120M83G1 E-10 F300M121
18:02:56: M120M83G1 E-10 F300M121
18:02:38: M0 H1: Cancelled printing file 0:/gcodes/3D print with template UPPE REAR.gcode, print time was 0h 1m
18:02:25: : Printing paused at X478.0 Y349.2 Z0.4
18:02:14: : Resume state saved
18:02:11: M24: Printing resumed
18:01:32: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 40.72mm/rev, min 1% max 164% over 62.3mm
18:01:31: : Printing paused at X775.7 Y347.1 Z0.4
18:01:18: : Resume state saved
18:01:15: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 24.91mm/rev, min 100% max 100% over 36.9mm
18:01:13: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, no calibration data
18:01:11: M591 D0: Printing resumedDuet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 28.26mm/rev, min 0% max 114% over 179.3mm
18:00:32: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 107, measured sensitivity 28.26mm/rev, min 0% max 114% over 179.3mm
18:00:31: : Printing paused at X1109.6 Y274.7 Z0.4
18:00:15: : Resume state saved
17:59:54: M290 S0.05
17:59:53: M290 S0.05
17:59:52: M290 S0.05
17:59:52: M290 S0.05
17:59:51: M290 S0.05
17:59:03: M290 S-0.05
17:59:02: M290 S-0.05
17:58:59: M32 ""0:/gcodes/3D print with template UPPE REAR.gcode"": File 0:/gcodes/3D print with template UPPE REAR.gcode selected for printing
17:58:20: M0 H1: Printing paused at X812.7 Y285.0 Z0.4Cancelled printing file 0:/gcodes/3D print with template UPPE REAR.gcode, print time was 0h 8m
17:58:07: M25: Resume state saved
17:54:59: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 107, measured sensitivity 25.15mm/rev, min 24% max 101% over 2165.4mm
17:54:32: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 107, measured sensitivity 25.17mm/rev, min 24% max 102% over 1946.2mm
17:53:38: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 131 agc 107, measured sensitivity 25.23mm/rev, min 24% max 102% over 1520.3mm
17:53:14: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 25.18mm/rev, min 24% max 102% over 1311.7mm
17:53:12: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 25.18mm/rev, min 24% max 102% over 1311.7mm
17:53:10: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 25.19mm/rev, min 24% max 102% over 1287.0mm
17:52:43: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 25.24mm/rev, min 24% max 102% over 1027.8mm
17:52:28: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 25.28mm/rev, min 24% max 102% over 892.5mm
17:52:26: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 25.28mm/rev, min 24% max 102% over 880.1mm
17:52:24: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 25.29mm/rev, min 24% max 102% over 855.3mm
17:52:23: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 25.29mm/rev, min 24% max 102% over 843.0mm
17:52:21: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 25.30mm/rev, min 24% max 102% over 830.6mm
17:52:12: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 25.34mm/rev, min 24% max 102% over 744.1mm
17:52:00: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 25.40mm/rev, min 24% max 103% over 645.1mm
17:51:44: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 25.55mm/rev, min 24% max 103% over 496.6mm
17:51:28: M290 S-0.05
17:51:27: M290 S-0.05
17:51:26: M290 S-0.05
17:51:26: M290 S-0.05
17:51:13: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 26.45mm/rev, min 25% max 107% over 211.8mm
17:51:11: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 26.66mm/rev, min 25% max 108% over 187.4mm
17:51:10: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 26.66mm/rev, min 25% max 108% over 187.4mm
17:51:09: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 26.78mm/rev, min 25% max 108% over 175.4mm
17:51:08: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 26.94mm/rev, min 25% max 108% over 163.4mm
17:51:07: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 27.10mm/rev, min 26% max 109% over 151.0mmDuet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 27.10mm/rev, min 26% max 109% over 151.0mm
17:51:05: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 27.32mm/rev, min 26% max 110% over 138.6mm
17:51:04: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 27.56mm/rev, min 26% max 111% over 126.4mm
17:50:58: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 30.68mm/rev, min 29% max 123% over 64.7mm
17:50:54: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 35.36mm/rev, min 33% max 142% over 40.0mm
17:50:52: M591 D0: Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, no calibration data
17:50:49: M591 D0: Printing resumedDuet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 25735.67mm/rev, min 100% max 100% over 25.1mm
17:50:27: M290 S0.05
17:50:27: M290 S0.05
17:50:13: : Printing paused at X671.9 Y349.1 Z0.4
17:50:01: : Resume state saved
17:49:58: M24: Printing resumed
17:49:20: M591 D0: Printing paused at X943.1 Y340.9 Z0.4Duet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 14107.09mm/rev, min 100% max 100% over 27.6mmDuet3D magnetic filament monitor with switch on input 3, enabled, sensitivity 24.85mm/rev, allow 3% to 300%, check every 12.0mm, version 3, mag 132 agc 107, measured sensitivity 14107.09mm/rev, min 100% max 100% over 27.6mm
17:49:05: : Resume state saved
17:49:01: M24: Printing resumed
17:48:46: M290 S0.05
17:48:45: M290 S0.05
17:48:45: M290 S0.05
17:48:22: : Printing paused at X1109.6 Y274.7 Z0.4
17:48:06: : Resume state saved
17:47:59: M24: Printing resumed
17:47:49: M290 S0.05
17:47:48: M290 S0.05
17:47:47: M290 S0.05
17:47:41: : Printing paused at X633.0 Y274.7 Z0.4
17:47:30: : Resume state saved
17:47:29: M290 S-0.05
17:46:33: M32 ""3D print with template UPPE REAR.gcode"": File 3D print with template UPPE REAR.gcode selected for printing
17:33:27: G29: 210 points probed, min error -0.372, max error 0.380, mean 0.029, deviation 0.148Height map saved to file heightmap.csv
17:14:06: G28
17:13:54: G29: Error: G29: Must home printer before bed probing
17:13:47: M292
17:11:13: M292
17:06:15: M292
17:00:16: G28
16:59:52: Connection established!
1