M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956L2-G43S8-6J9FA-3SJ6M-1B0UG
Used output buffers: 1 of 40 (10 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 62080 of which 184 recycled
Never used RAM 138168, free system stack 153 words
Tasks: SBC(ready,51.3%,328) HEAT(delaying,0.4%,325) Move(notifyWait,1.3%,284) CanReceiv(notifyWait,0.0%,878) CanSender(notifyWait,0.0%,374) CanClock(delaying,0.2%,339) TMC(notifyWait,12.0%,59) MAIN(running,34.7%,922) IDLE(ready,0.0%,29), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 45:49:21 ago, cause: power up
Last software reset at 2022-02-01 16:04, reason: User, none spinning, available RAM 141024, slot 1
Software reset code 0x0012 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
Step timer max interval 155
MCU temperature: min 31.4, current 39.2, max 40.6
Supply voltage: min 23.9, current 24.0, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 11.7, current 12.0, max 12.7, under voltage events: 0
Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/8/8, gc cycles 0
Driver 0: position -1600, standstill, reads 64275, writes 28 timeouts 0, SG min/max 0/1023
Driver 1: position -160, standstill, reads 64275, writes 28 timeouts 0, SG min/max 0/1023
Driver 2: position 0, standstill, reads 64284, writes 19 timeouts 0, SG min/max 0/145
Driver 3: position 0, standstill, reads 64284, writes 19 timeouts 0, SG min/max 0/142
Driver 4: position 0, standstill, reads 64293, writes 11 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 64293, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2022-02-03 14:02:18
Slowest loop: 72.92ms; fastest: 0.04ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 82772290ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 10, completed moves 10, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0: no data received
=== CAN ===
Messages queued 1484766, received 193, lost 0, longest wait 105ms for reply type 6018, peak Tx sync delay 61663, free buffers 49 (min 48), ts 824808/824807/0
Tx timeouts 0,0,0,0,0,0
=== SBC interface ===
State: 4, failed transfers: 1, checksum errors: 0
Last transfer: 1ms ago
RX/TX seq numbers: 23546/23546
SPI underruns 0, overruns 0
Disconnects: 0, timeouts: 0, IAP RAM available 0x2c810
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.3.0
Code buffer space: 4096
Configured SPI speed: 8000000Hz
Full transfers per second: 35.41, max wait times: 31.1ms/0.0ms
Codes per second: 0.00
Maximum length of RX/TX data transfers: 3008/820