M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.3 (2021-06-15 21:46:11) running on Duet 3 Mini5plus Ethernet (standalone mode)
Board ID: 4NVUV-F396U-D65J0-40KMJ-0D03Z-7SU7W
Used output buffers: 3 of 40 (31 max)
=== RTOS ===
Static ram: 102724
Dynamic ram: 102376 of which 0 recycled
Never used RAM 35748, free system stack 120 words
Tasks: NETWORK(ready,83.8%,240) ETHERNET(notifyWait,0.7%,568) SENSORS(delaying,0.0%,100) HEAT(notifyWait,0.1%,344) Move(notifyWait,0.4%,286) CanReceiv(notifyWait,0.0%,941) CanSender(notifyWait,0.0%,371) CanClock(delaying,0.1%,332) TMC(notifyWait,4.4%,106) MAIN(running,7.3%,426) IDLE(ready,0.0%,29) AIN(delaying,3.1%,264), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 04:34:59 ago, cause: software
Last software reset at 2022-02-21 10:37, reason: User, GCodes spinning, available RAM 35748, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
MCU revision 3, ADC conversions started 16499119, completed 16499119, timed out 0, errs 0
Step timer max interval 752
MCU temperature: min 21.5, current 23.3, max 23.6
Supply voltage: min 24.0, current 24.0, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/1, heap memory allocated/used/recyclable 2048/24/0, gc cycles 0
Driver 0: position 33378, ok, SG min/max 0/410, read errors 0, write errors 1, ifcnt 42, reads 58091, writes 12, timeouts 0, DMA errors 0
Driver 1: position 1243, ok, SG min/max 0/412, read errors 0, write errors 1, ifcnt 40, reads 58092, writes 11, timeouts 0, DMA errors 0
Driver 2: position 71130, ok, SG min/max 0/412, read errors 0, write errors 1, ifcnt 40, reads 58092, writes 11, timeouts 0, DMA errors 0
Driver 3: position 0, ok, SG min/max 0/110, read errors 0, write errors 1, ifcnt 37, reads 58092, writes 11, timeouts 0, DMA errors 0
Driver 4: position 0, ok, SG min/max 0/2, read errors 0, write errors 1, ifcnt 38, reads 58092, writes 11, timeouts 0, DMA errors 0
Driver 5: position 0, ok, SG min/max 0/412, read errors 0, write errors 1, ifcnt 40, reads 58092, writes 11, timeouts 0, DMA errors 0
Driver 6: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 29, reads 58094, writes 9, timeouts 0, DMA errors 0
Date/time: 2022-02-21 15:12:33
Cache data hit count 4294967295
Slowest loop: 167.42ms; fastest: 0.08ms
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 4.4ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 32960ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 57662, completed moves 57655, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state 3
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 1.0
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is doing "G1 X299.157 Y299.157 E50.91918" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0: pos 189.84, errs: frame 10 parity 0 ovrun 0 pol 2 ovdue 0
=== CAN ===
Messages queued 148491, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 17 (min 17), ts 82496/0/0
Tx timeouts 0,0,82495,0,0,65994 last cancelled message type 30 dest 127

=== Network ===
Slowest loop: 212.60ms; fastest: 0.03ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- Ethernet -
State: active
Error counts: 0 0 0 0 0
Socket states: 2 2 2 2 2 0 0 0