; Configuration file for Duet WiFi (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.2.3 on Tue May 04 2021 22:49:42 GMT+0200 (Ora legale dell’Europa centrale) ; General preferences G90 ; send absolute coordinates... M564 S1 H0 M83 ; ...but relative extruder moves M550 P" PAOLO ZAMPINI" ; set printer name ; Network M540 P40:f5:20:0d:6b:49 ; MAC Address M552 S1 ; s1 enable s0 disable network M587 S"infinity" P"cccccccc" I192.168.1.15 ; IP address M554 192.168.1.1 ; Gateway M553 255.255.255.0 ; Netmask M586 P0 S1 ; enable HTTP M586 P1 S1 ; enable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S0 R-1 ; X physical drive 0 goes forwards M569 P1 S0 R1 ; Y physical drive 1 goes forwards M569 P2 S1 ; Z physical drive 2 goes forwards M569 P3 S0 ; E0 physical drive 3 goes forwards M569 P4 S0 ; E1 physical drive 4 goes forwards M569 P5 S0 ; E2 physical drive 5 goes forwards M569 P6 S0 ; E3 physical drive 6 goes forwards M569 P7 S0 R1 T5:5:10:10 ; E4 X physical drive 7 goes forwards M569 P8 S1 R1 T5:5:10:10 ; E5 Y physical drive 8 goes forwards M569 P9 S1 R-1 ; E6 Z physical drive 9 goes forwards M584 X7 Y8 Z1:2 E3:4:5:6 S0 ; set drive mapping M671 X0:0 Y0:0 S0.5 ; leadscrews at left (connected to Z) and right (connected to E1) of X axis M350 X16 Y16 Z16 E16:16:16:16 I1 ; configure microstepping without interpolation M92 X99.975 Y99.975 Z800.10 E392.70:392.70:392.70:392.70 ; set steps per mm M566 X1000.00 Y1000.00 Z1500.00 E5000.00:5000.00:5000.00:5000.00 ; set maximum instantaneous speed changes (mm/min) M203 X10000.00 Y10000.00 Z4500.00 E10000.00:10000.00:10000.00:10000.00 ; set maximum speeds (mm/min) M201 X1000.00 Y1000.00 Z1500.00 E4000.00:4000.00:4000.00:4000.00 ; set accelerations (mm/s^2) M906 X0 Y2000 Z2000 E1500:1500:0:0 I90 ; set motor currents (mA) and motor idle factor in per cent M84 S15 ; Set idle timeout ; Axis Limits M208 X-25 Y10 Z0 S1 ; set axis minima M208 X500 Y500 Z300 S0 ; set axis maxima ; Endstops M574 X0 S1 P"!xstop" ; configure active-high endstop for low end on X via pin xstop M574 Y1 S1 P"!ystop" ; configure active-high endstop for low end on Y via pin ystop ;M574 Z2 S1 P"!zstop+!duex.e5stop" ; configure active-high endstop for low end on Z via pin null M574 Z1 S1 P"!zstop+!e1stop" ;Filament Sensing M591 P2 C"e0stop" S0 D0 ;04 nozle s1=on s0=off D = 0 or 1 or 2 or 3 Number Sensing M591 P2 C"duex.e2stop" S1 D2 ;08 nozle s1=on s0=off D = 0 or 1 or 2 or 3 Number Sensing M591 P2 C"duex.e3stop" S1 D3 ;1.2 nozle s1=on s0=off D = 0 or 1 or 2 or 3 Number Sensing M591 P2 C"duex.e4stop" S1 D4 ;2.3 nozle s1=on s0=off D = 0 or 1 or 2 or 3 Number Sensing ; Z-Probe M556 S50 X0 Y0 Z0 ; set orthogonal axis compensation parameters M557 X15:415 Y15:400 S20 ; define mesh grid ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M307 H0 B1 S2.00 ; enable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S140 ; set temperature limit for heater 0 to 140C M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit D10= SECONDI RITARDO ERRORE M143 H1 S280 ; set temperature limit for heater 1 to 280C M308 S2 P"e1temp" Y"thermistor" T100000 B4138 ; configure sensor 2 as thermistor on pin duex.e2temp M950 H2 C"e1heat" T2 ; create nozzle heater output on !duex.e2heat and map it to sensor 2 M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit D10= SECONDI RITARDO ERRORE M143 H2 S280 ; set temperature limit for heater 2 to 280C M308 S3 P"duex.e2temp" Y"thermistor" T100000 B3950 R2200 ; configure sensor 3 as PT1000 on pin duex.e3temp M950 H3 C"duex.e2heat" T3 ; create nozzle heater output on duex.e3heat and map it to sensor 3 M307 H3 B0 S0.00 ; disable bang-bang mode for heater and set PWM limit D10= SECONDI RITARDO ERRORE M143 H3 S280 ; set temperature limit for heater 3 to 280C M308 S4 P"duex.e3temp" Y"thermistor" T100000 B3950 R2200 ; configure sensor 4 as PT1000 on pin duex.e3temp M950 H4 C"duex.e3Heat" T4 ; create nozzle heater output on duex.e4heat and map it to sensor 4 M307 H4 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit D10= SECONDI RITARDO ERRORE M143 H4 S280 ; set temperature limit for heater 3 to 280C ; Fans M950 F1 C"fan1" Q600 ; create fan 0 on pin fan0 and set its frequency M106 P1 S100 H1 T10 ; set fan 0 value. Thermostatic control is turned off M950 F4 C"fan2" Q600 ; create fan 0 on pin fan0 and set its frequency M106 P4 S100 H1 T100 ; set fan 0 value. Thermostatic control is turned off M950 F7 C"!duex.fan7" Q500 ; create fan 1 on pin fan1 and set its frequency M950 P7 S1 H-1 ; set fan 1 value. Thermostatic control is turned on ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C M563 P1 D1 H2 F0 ; define tool 1 G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C M563 P2 D2 H3 F0 ; define tool 2 G10 P2 X0 Y0 Z0 ; set tool 2 axis offsets G10 P2 R0 S0 ; set initial tool 2 active and standby temperatures to 0C M563 P3 D3 H4 F0 ; define tool 3 G10 P3 X0 Y0 Z0 ; set tool 3 axis offsets G10 P3 R0 S0 ; set initial tool 3 active and standby temperatures to 0C ; Custom settings are not defined ; Miscellaneous M575 P1 S1 B57600 ; enable support for PanelDue M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss T0 ; select first tool M302 S20 R20 ;M572 D0 S0.0 ;04 nozle M572 D1 S0.25 ;08 nozle ;M572 D2 S0.8 ;1.2 nozle ;M572 D3 S1.2 ;2.3 nozle M501 ; load saved parameters from non-volatile memory