5/18/2022, 11:45:47 AM: Connected to 192.168.0.1 5/18/2022, 11:45:58 AM: M122: === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later + DueX5 Board ID: 0JD0M-9X6JA-JUNSS-6J9D4-3S46T-9BJZU Used output buffers: 3 of 24 (24 max) === RTOS === Static ram: 23876 Dynamic ram: 76520 of which 0 recycled Never used RAM 11164, free system stack 114 words Tasks: NETWORK(ready,62.5%,233) HEAT(delaying,0.1%,326) Move(notifyWait,0.5%,303) DUEX(notifyWait,0.0%,24) MAIN(running,36.8%,441) IDLE(ready,0.2%,29), total 100.0% Owned mutexes: WiFi(NETWORK) === Platform === Last reset 01:36:14 ago, cause: power up Last software reset at 2022-05-17 23:31, reason: User, GCodes spinning, available RAM 11164, slot 2 Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a Error status: 0x04 Aux0 errors 0,1,0 Step timer max interval 0 MCU temperature: min 15.5, current 21.9, max 22.5 Supply voltage: min 23.9, current 24.2, max 24.7, under voltage events: 0, over voltage events: 0, power good: yes Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/52/52, gc cycles 0 Driver 0: position 100, standstill, SG min/max 0/315 Driver 1: position 100, standstill, SG min/max 0/339 Driver 2: position 10649, standstill, SG min/max 0/290 Driver 3: position 0, standstill, SG min/max 0/1023 Driver 4: position 0, standstill, SG min/max not available Driver 5: position 0, standstill, SG min/max 0/375 Driver 6: position 0, standstill, SG min/max 0/292 Driver 7: position 0, standstill, SG min/max not available Driver 8: position 0, standstill, SG min/max 0/242 Driver 9: position 0, standstill, SG min/max 0/259 Driver 10: position 0 Driver 11: position 0 Date/time: 2022-05-18 11:45:53 Cache data hit count 4294967295 Slowest loop: 222.33ms; fastest: 0.09ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Storage === Free file entries: 8 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest read time 9.1ms, write time 127.9ms, max retries 0 === Move === DMs created 83, maxWait 363151ms, bed compensation in use: mesh, comp offset 0.000 === MainDDARing === Scheduled moves 4688, completed moves 4688, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 1], CDDA state -1 === AuxDDARing === Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === Heat === Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1 Heater 0 is on, I-accum = 0.6 === GCodes === Segments left: 0 Movement lock held by Autopause HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 Daemon is idle in state(s) 0 Autopause is doing "T-1 P0[0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09][0x09]" in state(s) 0 32, running macro Code queue is not empty: Queued 'M300 S1111 P333 ' for move 4688 Queued 'M106 S0 ' for move 4688 2 of 16 codes have been queued. === Filament sensors === Extruder 0 sensor: ok Extruder 1 sensor: ok === DueX === Read count 1, 0.01 reads/min === Network === Slowest loop: 80.21ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions HTTP sessions: 1 of 8 - WiFi - Network state is active WiFi module is providing access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.23 WiFi MAC address be:ff:4d:e8:31:0d WiFi Vcc 3.34, reset reason Power up WiFi flash size 2097152, free heap 24400 WiFi IP address 192.168.0.1 Connected clients 1 Clock register ffffffff Socket states: 0 0 0 0 0 0 0 0