PK á9³TÈÅ‚ DD homeall.g; homeall.g ; called to home all axes ; ; generated by RepRapFirmware Configuration Tool v3.3.10 on Sat Dec 18 2021 07:55:06 GMT+0000 (Greenwich Mean Time) G91 ; relative positioning G1 H2 Z25 F6000 ; lift Z relative to current position ; X Axis G1 H1 X350 F4000 ; move quickly to X endstop and stop there (first pass) G1 X-5 F6000 ; go back a few mm G1 H1 X350 F360 ; move slowly to X axis endstop once more (second pass) G1 H1 X350 ; then move slowly to X axis endstop ; Y Axis G1 H1 Y350 F4000 ; move quickly to Y axis endstop and stop there (first pass) G1 Y-5 F6000 ; go back a few mm G1 H1 Y350 F360 ; move slowly to Y axis endstop once more (second pass) G1 H1 Y350 ; then move slowly to Y axis endstop ; Z Axis ;G91 ; relative positioning ;G1 H1 Z25 F1000 ; lift Z relative to current position G90 ; absolute positioning G1 X150 Y150 F6000 ; Go to the bed centre & probe point and home the Z axis G1 H1 Z-99999 F1000 ; move Z down until the endstop is triggered G1 H0 Z25 F1000 ; lift Z 25mm G1 H1 Z-100 F400 ; G30 ; Calibrate Z-axis ; G92 Z0 ; set Z position to axis minimum (you may want to adjust this) G1 H0 Z25 F6000 ; lift nozzle PK á9³Tim€homex.g; homex.g ; called to home the X axis ; ; generated by RepRapFirmware Configuration Tool v3.3.10 on Sat Dec 18 2021 07:55:06 GMT+0000 (Greenwich Mean Time) G91 ; relative positioning G1 H2 Z5 F6000 ; lift Z relative to current position G1 H1 X350 F5200 ; move quickly to X axis endstop and stop there (first pass) G1 X-5 F6000 ; go back a few mm G1 H1 X350 F360 ; move slowly to X axis endstop once more (second pass) G1 H2 Z-5 F6000 ; lower Z again G90 ; absolute positioning PK á9³TÍlhomey.g; homey.g ; called to home the Y axis ; ; generated by RepRapFirmware Configuration Tool v3.3.10 on Sat Dec 18 2021 07:55:06 GMT+0000 (Greenwich Mean Time) G91 ; relative positioning G1 H2 Z5 F6000 ; lift Z relative to current position G1 H1 Y350 F5200 ; move quickly to Y axis endstop and stop there (first pass) G1 Y-5 F6000 ; go back a few mm G1 H1 Y350 F360 ; move slowly to Y axis endstop once more (second pass) G1 H2 Z-5 F6000 ; lower Z again G90 ; absolute positioning PK á9³Ts),  homez.g; homez.g ; called to home the Z axis ; ; generated by RepRapFirmware Configuration Tool v3.3.10 on Sat Dec 18 2021 07:55:06 GMT+0000 (Greenwich Mean Time) G90 ; absolute positioning G1 H1 Z15 F6000 ; lift Z relative to current position G90 ; absolute positioning G1 X150 Y150 F6000 ; Go to the bed centre & probe point and home the Z axis G1 H1 Z-99999 F1000 ; move Z down until the endstop is triggered G1 H0 Z25 F4000 ; lift Z 25mm G1 H1 Z-100 F400 ; G30 ; Calibrate Z-axis ; G92 Z0 ; set Z position to axis minimum (you may want to adjust this) G1 H0 Z25 F6000 ; lift nozzle ; Uncomment the following lines to lift Z after probing ;G91 ; relative positioning ;G1 Z50 F500 ; lift Z relative to current position ;G90 ; absolute positioning ; M290 S0.3 ; set baby stepping PK á9³TÈÅ‚ DD homeall.gPK á9³Tim€khomex.gPK á9³TÍl•homey.gPK á9³Ts),  ¿ homez.gPKÖ„