13/10/2022, 09:24:53: Connected to 192.168.1.15 13/10/2022, 09:25:06: M122 13/10/2022, 09:25:14: M122 13/10/2022, 09:25:16: M122 13/10/2022, 09:25:24: M122 13/10/2022, 09:26:11: M122: === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.2 (2022-09-13 15:11:16) running on Duet WiFi 1.02 or later + DueX2v0.11 Board ID: 0JD2M-9F8TA-GJ4TD-6J9F2-3S06P-KQNA7 Used output buffers: 4 of 26 (26 max) === RTOS === Static ram: 23860 Dynamic ram: 77028 of which 44 recycled Never used RAM 11148, free system stack 174 words Tasks: NETWORK(ready,42.9%,237) HEAT(notifyWait,0.0%,317) Move(notifyWait,0.0%,363) DUEX(notifyWait,0.0%,24) MAIN(running,57.1%,410) IDLE(ready,0.0%,30), total 100.0% Owned mutexes: WiFi(NETWORK) === Platform === Last reset 00:02:12 ago, cause: power up Last software reset at 2022-10-12 13:37, reason: User, GCodes spinning, available RAM 7976, slot 0 Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00417000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a Error status: 0x04 Aux0 errors 0,0,0 Step timer max interval 0 MCU temperature: min 29.1, current 30.1, max 30.1 Supply voltage: min 23.9, current 24.2, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0 Events: 0 queued, 0 completed Driver 0: standstill, SG min n/a Driver 1: standstill, SG min n/a Driver 2: standstill, SG min n/a Driver 3: standstill, SG min n/a Driver 4: standstill, SG min n/a Driver 5: standstill, SG min n/a Driver 6: standstill, SG min n/a Driver 7: Driver 8: Driver 9: Driver 10: Driver 11: Date/time: 2022-10-13 09:26:10 Cache data hit count 4294967295 Slowest loop: 22.67ms; fastest: 0.20ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Storage === Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest read time 0.3ms, write time 0.0ms, max retries 0 === Move === DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000 === MainDDARing === Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === AuxDDARing === Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === Heat === Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0 Heater 1 is on, I-accum = 0.0 === GCodes === Segments left: 0 Movement lock held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 Daemon is idle in state(s) 0 Autopause is idle in state(s) 0 Code queue is empty === Filament sensors === Extruder 0 sensor: ok Extruder 1 sensor: ok === DueX === Read count 0, 0.00 reads/min === Network === Slowest loop: 243.36ms; fastest: 0.07ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions HTTP sessions: 1 of 8 = WiFi = Network state is active WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.27 WiFi MAC address e8:68:e7:7f:6d:82 WiFi Vcc 3.46, reset reason Power up WiFi flash size 2097152, free heap 24264 WiFi IP address 192.168.1.15 WiFi signal strength -65dBm, mode 802.11n, reconnections 0, sleep mode modem Clock register 00002002 Socket states: 0 0 0 0 0 0 0 0 13/10/2022, 09:26:47: Download of config.g successful after 0s 13/10/2022, 09:30:04: M98 P"config.g" 13/10/2022, 09:30:13: M98 P"config.g" 13/10/2022, 09:30:25: M98 P"config.g" 13/10/2022, 09:30:27: M98 P"config.g" 13/10/2022, 09:30:46: M98 P"config.g" 13/10/2022, 09:31:35: M98 P"config.g": Gateway: 0.0.0.0 Net mask: 255.255.255.0 HTTP is enabled on port 80 FTP is enabled on port 21 TELNET is disabled Error: bad model parameters