10/28/2022, 7:17:14 PM: Connected to 192.168.1.119
10/28/2022, 7:17:45 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03beta3 running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9K662-MG5TD-6JKDA-3S06T-KBJUZ
Used output buffers: 1 of 20 (13 max)
=== RTOS ===
Static ram: 25632
Dynamic ram: 94340 of which 0 recycled
Exception stack ram used: 328
Never used ram: 10772
Tasks: NETWORK(ready,524) HEAT(blocked,1236) MAIN(running,3816) IDLE(ready,196)
Owned mutexes:
=== Platform ===
Last reset 00:01:40 ago, cause: power up
Last software reset at 2022-10-28 14:11, reason: User, spinning module GCodes, available RAM 10536 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 17.3, current 22.7, max 22.9
Supply voltage: min 23.9, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2022-10-28 19:17:43
Cache data hit count 350053483
Slowest loop: 6.00ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0
=== Move ===
Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0, aux move: no
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 16.08ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address d8:f1:5b:10:5f:23
WiFi Vcc 3.42, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 25992
WiFi IP address 192.168.1.119
WiFi signal strength -41dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
10/28/2022, 7:20:35 PM: M98 P"config.g": HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Warning: M308 command is not supported
Warning: M950 command is not supported
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 241C.
Warning: M308 command is not supported
Warning: M950 command is not supported
Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 683C.
Warning: M308 command is not supported
Warning: M950 command is not supported
Warning: Heater 2 appears to be over-powered. If left on at full power, its temperature is predicted to reach 681C.
Warning: M950 command is not supported
Warning: M950 command is not supported
Warning: M950 command is not supported
Warning: M308 command is not supported
Warning: M308 command is not supported
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 241C.
Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 683C.
Warning: Heater 2 appears to be over-powered. If left on at full power, its temperature is predicted to reach 681C.