01/01/2023 20:00:45: m122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.5beta1+ (2022-12-31 15:22:06) running on Duet 3 MB6HC v1.01 (SBC mode)
Board ID: 08DJM-956L2-G43S8-6J9FJ-3S86S-983QD
Used output buffers: 1 of 40 (28 max)
=== RTOS ===
Static ram: 151308
Dynamic ram: 73220 of which 124 recycled
Never used RAM 125756, free system stack 144 words
Tasks: SBC(resourceWait:,0.7%,436) HEAT(notifyWait,0.0%,321) Move(notifyWait,0.0%,265) CanReceiv(notifyWait,0.0%,943) CanSender(notifyWait,0.0%,335) CanClock(delaying,0.0%,334) TMC(notifyWait,8.3%,60) MAIN(running,90.3%,953) IDLE(ready,0.7%,30), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:06:50 ago, cause: software
Last software reset at 2023-01-01 18:53, reason: User, GCodes spinning, available RAM 125476, slot 0
Software reset code 0x6003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 134
MCU temperature: min 33.1, current 33.2, max 33.8
Supply voltage: min 23.9, current 23.9, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.0, max 12.1, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 0, mspos 552, reads 39880, writes 19 timeouts 0
Driver 1: standstill, SG min 18, mspos 424, reads 39881, writes 19 timeouts 0
Driver 2: standstill, SG min 26, mspos 520, reads 39881, writes 19 timeouts 0
Driver 3: standstill, SG min 30, mspos 440, reads 39881, writes 19 timeouts 0
Driver 4: standstill, SG min n/a, mspos 8, reads 39884, writes 16 timeouts 0
Driver 5: standstill, SG min n/a, mspos 8, reads 39889, writes 11 timeouts 0
Date/time: 2023-01-01 19:00:44
Slowest loop: 90.68ms; fastest: 0.04ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 11, maxWait 395004ms, bed compensation in use: none, comp offset 0.000
no step interrupt scheduled
=== DDARing 0 ===
Scheduled moves 8, completed 8, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.5
=== GCodes ===
Movement locks held by null, null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2* is doing "M0" in state(s) 0, sync state 1
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x1000007
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== CAN ===
Messages queued 3670, received 0, lost 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 50 (min 50), ts 2051/0/0
Tx timeouts 0,0,2050,0,0,1618 last cancelled message type 30 dest 127
=== SBC interface ===
Transfer state: 5, failed transfers: 0, checksum errors: 0
RX/TX seq numbers: 18528/18528
SPI underruns 0, overruns 0
State: 5, disconnects: 0, timeouts: 0 total, 0 by SBC, IAP RAM available 0x29b74
Buffer RX/TX: 0/0-0, open files: 0
=== Duet Control Server ===
Duet Control Server version 3.5.0-b1 (2022-12-23 20:41:36)
File2+ProcessInternally:

File /opt/dsf/sd/gcodes/CFFFP_Anthony powerbox.gcode is selected, processing
File2:
Buffered code: M0
==> 24 bytes
Code buffer space: 4096
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 0
Full transfers per second: 45.50, max time between full transfers: 376.3ms, max pin wait times: 52.3ms/6.0ms
Codes per second: 47.47
Maximum length of RX/TX data transfers: 4236/1884