; Configuration file for Duet Maestro (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.1 on Sat May 30 2020 16:52:37 GMT+0100 (British Summer Time)

; General preferences
G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 P"TRONXY BOT MAESTRO"                     ; set printer name

; Network
 M552 S1
 M552 P0.0.0.0                                  ; enable network and acquire dynamic address via DHCP
;M586 P0 S1                                     ; enable HTTP
;M586 P1 S0                                     ; disable FTP
;M586 P2 S0                                     ; disable Telnet
 
; Drives
M669 K1
M569 P0 S0                                     ; physical drive x 0 goes backwards 1 goes forwards
M569 P1 S0                                     ; physical drive y 
M569 P2 S0                                     ; physical drive z1 
M569 P3 S0                                     ; physical drive e0(extruder) 
M569 P4 S0                                     ; physical drive z2

M584 X0                                        ; set drive mapping
M584 Y1
M584 Z2:4
M854 E3

M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
M92 X80 Y80 Z400 E402.14                       ; set steps per mm
M566 X600.00 Y600.00 Z24.00 E1200.00           ; set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z1000.00 E3000.00     ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z120.00 E500.00         ; set accelerations (mm/s^2)
M906 X1400 Y1400 Z1400 E800 I30                ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                        ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                               ; set axis minima
M208 X230 Y300 Z230 S0                         ; set axis maxima

; Endstops
M574 X1 S1 P"!xstop"                           ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"!ystop"                           ; configure active-high endstop for low end on Y via pin ystop
M574 Z2 S1 P"!zstop+!e1stop"                   ; configure active-high endstop for low end on Z via pin zstop


;M591 D0 P2 C"e0stop" S1                       ;filament runout


; Z-Probe
;M558 P0 H5 F120 T6000                          ; disable Z probe but set dive height, probe speed and travel speed
;M557 X15:205 Y15:195 S20                       ; define mesh grid

; Heaters

M308 S0 P"bedtemp" Y"thermistor" T100000 B4138        ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" Q10 T0                             ; create bed heater output on bedheat and map it to sensor 0 at 10Hz
M307 H0 B0 S1.00                                      ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                               ; map heated bed to heater 0
M143 H0 S100                                          ; set temperature limit for heater 0 to 100C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725         ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                                  ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                                      ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S255                                          ; set nozzle max temp to 255C
   

; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q300                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                              ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                               ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                           ; load saved parameters from non-volatile memory