m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6XD version 3.4.5 (2022-11-30 19:41:59) running on Duet 3 MB6XD v1.0 or later (SBC mode)
Board ID: 08DLM-956DA-M24S4-7J9D8-3SD6N-1UMAT
Used output buffers: 1 of 40 (17 max)
=== RTOS ===
Static ram: 151200
Dynamic ram: 69464 of which 0 recycled
Never used RAM 126240, free system stack 154 words
Tasks: SBC(ready,0.7%,487) HEAT(notifyWait,0.0%,351) Move(notifyWait,0.1%,256) CanReceiv(notifyWait,0.0%,797) CanSender(notifyWait,0.0%,328) CanClock(delaying,0.0%,351) MAIN(running,97.5%,976) IDLE(ready,1.7%,29), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:04:06 ago, cause: software
Last software reset at 2023-04-18 18:45, reason: User, Platform spinning, available RAM 126480, slot 0
Software reset code 0x0000 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
Step timer max interval 18727
MCU temperature: min 38.7, current 39.1, max 39.9
Supply voltage: min 24.0, current 24.6, max 24.8, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/12/12, gc cycles 0
Events: 2 queued, 2 completed
Driver 0: ok
Driver 1: ok
Driver 2: ok
Driver 3: ok
Driver 4: ok
Driver 5: ok
Date/time: 2023-04-18 18:50:05
Slowest loop: 2000.69ms; fastest: 0.03ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 38, maxWait 84939ms, bed compensation in use: mesh, comp offset -0.020
=== MainDDARing ===
Scheduled moves 432, completed 432, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters 3 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause* is idle in state(s) 0
Code queue is empty
=== Filament sensors ===
Extruder 0: no data received
Extruder 1: no data received
=== CAN ===
Messages queued 2648, received 10022, lost 0, boc 0
Longest wait 5ms for reply type 4014, peak Tx sync delay 8, free buffers 50 (min 35), ts 1234/1233/0
Tx timeouts 0,0,0,0,0,0
=== SBC interface ===
Transfer state: 5, failed transfers: 0, checksum errors: 0
RX/TX seq numbers: 10027/10027
SPI underruns 0, overruns 0
State: 5, disconnects: 0, timeouts: 0 total, 0 by SBC, IAP RAM available 0x2b748
Buffer RX/TX: 0/0-0, open files: 0
=== Duet Control Server ===
Duet Control Server v3.4.5
Code buffer space: 4096
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 0
Full transfers per second: 41.14, max time between full transfers: 108.5ms, max pin wait times: 51.9ms/11.0ms
Codes per second: 3.18
Maximum length of RX/TX data transfers: 3916/1572