9/22/2023, 3:55:22 PM	SD read speed for 500.0MByte file was 1.54MBytes/sec
9/22/2023, 3:49:58 PM	SD write speed for 500.0MByte file was 4.33MBytes/sec
Testing SD card read speed...
9/22/2023, 3:48:03 PM	M122 P104 S500
Testing SD card write speed...
9/22/2023, 3:43:48 PM	Connection established
9/22/2023, 3:43:48 PM	Failed to upload Tall Throne V5 Test.gcode
Could not complete action because the connection has been terminated
9/22/2023, 3:43:47 PM	Connection interrupted, attempting to reconnect...
HTTP request timed out
9/22/2023, 3:42:54 PM	Upload of nose cone mold THIS ONE.gcode successful after 27s
9/22/2023, 3:41:54 PM	SD read speed for 100.0MByte file was 1.56MBytes/sec
9/22/2023, 3:40:50 PM	SD write speed for 100.0MByte file was 4.40MBytes/sec
Testing SD card read speed...
9/22/2023, 3:40:27 PM	M122 P104 S100
Testing SD card write speed...
9/22/2023, 3:40:16 PM	SD read speed for 50.0MByte file was 1.58MBytes/sec
9/22/2023, 3:39:44 PM	SD write speed for 50.0MByte file was 4.43MBytes/sec
Testing SD card read speed...
9/22/2023, 3:39:33 PM	M122 P104 S50
Testing SD card write speed...
9/22/2023, 3:39:24 PM	SD read speed for 10.0MByte file was 1.65MBytes/sec
9/22/2023, 3:39:20 PM	SD write speed for 10.0MByte file was 2.89MBytes/sec
Testing SD card read speed...
9/22/2023, 3:39:16 PM	M122 P104 S10
Testing SD card write speed...
9/22/2023, 3:38:49 PM	m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6XD version 3.4.6 (2023-07-21 14:11:58) running on Duet 3 MB6XD v1.0 (standalone mode)
Board ID: 08DLM-956DA-M2NS4-6J1F6-3S86T-1B3US
Used output buffers: 1 of 40 (14 max)
=== RTOS ===
Static ram: 151692
Dynamic ram: 96284 of which 0 recycled
Never used RAM 98784, free system stack 114 words
Tasks: NETWORK(ready,30.5%,173) ETHERNET(notifyWait,4.7%,316) HEAT(notifyWait,1.2%,321) Move(notifyWait,6.1%,214) CanReceiv(notifyWait,4.3%,771) CanSender(notifyWait,6.8%,325) CanClock(delaying,0.6%,347) MAIN(running,45.8%,1102) IDLE(ready,0.0%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 147:53:40 ago, cause: software
Last software reset at 2023-09-16 11:45, reason: User, GCodes spinning, available RAM 102696, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 971
MCU temperature: min 36.0, current 36.6, max 39.5
Supply voltage: min 23.4, current 24.0, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.2, current 12.3, max 12.7, under voltage events: 0
Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/36/36, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: ok
Driver 1: ok
Driver 2: ok
Driver 3: ok
Driver 4: ok
Driver 5: ok
Date/time: 2023-09-22 15:38:46
Slowest loop: 3000.11ms; fastest: 0.03ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 5.1ms, write time 4.5ms, max retries 0
=== Move ===
DMs created 125, segments created 44, maxWait 278439ms, bed compensation in use: mesh, comp offset 0.546
=== MainDDARing ===
Scheduled moves 24202001, completed 24202001, hiccups 0, stepErrors 0, LaErrors 0, Underruns [8, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.0
Heater 2 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 28295695, received 21297162, lost 0, boc 0
Longest wait 3ms for reply type 6026, peak Tx sync delay 551, free buffers 50 (min 41), ts 2662102/2662101/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 268.93ms; fastest: 0.03ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
= Ethernet =
State: active
Error counts: 0 0 0 0 0 0
Socket states: 5 2 2 2 2 0 0 0
=== Multicast handler ===
Responder is inactive, messages received 0, responses 0
9/22/2023, 10:40:45 AM	Finished printing file 0:/gcodes/curved-2091611 2.gcode, print time was 142h 44m
9/16/2023, 12:06:53 PM	m376 h15
9/16/2023, 11:56:24 AM	M32 "0:/gcodes/curved-2091611 2.gcode"
File 0:/gcodes/curved-2091611 2.gcode selected for printing
9/16/2023, 11:54:11 AM	M0
Cancelled printing file 0:/gcodes/curved-2091611 2.gcode, print time was 0h 5m
9/16/2023, 11:54:08 AM	Printing paused at X1282.0 Y315.7 Z0.5
9/16/2023, 11:53:52 AM	M25
Resume state saved
9/16/2023, 11:48:50 AM	M32 "0:/gcodes/curved-2091611 2.gcode"
File 0:/gcodes/curved-2091611 2.gcode selected for printing
9/16/2023, 11:45:16 AM	Connection established
9/16/2023, 11:45:12 AM	Connection interrupted, attempting to reconnect...
9/16/2023, 11:45:03 AM	Emergency stop, attemping to reconnect...
9/16/2023, 11:45:01 AM	Upload of config.g successful after 0s