before reset:
	m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.5.0-beta.4 (2023-06-08 23:41:30) running on Duet 3 MB6HC v1.01 (standalone mode)
Board ID: 08DJM-9P63L-DJ3T0-6J9F0-3SN6L-TU37A
Used output buffers: 1 of 40 (38 max)
=== RTOS ===
Static ram: 155012
Dynamic ram: 123936 of which 0 recycled
Never used RAM 63276, free system stack 117 words
Tasks: NETWORK(1,ready,153.4%,182) ETHERNET(5,nWait,6.0%,392) HEAT(3,nWait,0.8%,323) Move(4,nWait,30.9%,214) CanReceiv(6,nWait,4.3%,769) CanSender(5,nWait,0.5%,326) CanClock(7,delaying,0.2%,349) TMC(4,nWait,163.9%,59) MAIN(1,running,78.7%,137) IDLE(0,ready,0.1%,30), total 438.8%
Owned mutexes:
=== Platform ===
Last reset 35:56:06 ago, cause: power up
Last software reset at 2023-11-04 14:45, reason: User, Gcodes spinning, available RAM 62236, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
MCU temperature: min 26.7, current 30.9, max 33.3
Supply voltage: min 23.6, current 23.8, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/284/284, gc cycles 0
Events: 1 queued, 1 completed
Driver 0: standstill, SG min 0, mspos 920, reads 18920, writes 156 timeouts 0
Driver 1: standstill, SG min 0, mspos 736, reads 18972, writes 104 timeouts 0
Driver 2: standstill, SG min 0, mspos 568, reads 18920, writes 156 timeouts 0
Driver 3: standstill, SG min 0, mspos 744, reads 18920, writes 156 timeouts 0
Driver 4: standstill, SG min 0, mspos 344, reads 18920, writes 156 timeouts 0
Driver 5: standstill, SG min 0, mspos 120, reads 18921, writes 156 timeouts 0
Date/time: 2023-11-06 02:41:53
Slowest loop: 216.88ms; fastest: 0.06ms
=== Storage ===
Free file entries: 20
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 9.3ms, write time 29.9ms, max retries 0
=== Move ===
DMs created 125, segments created 38, maxWait 29755146ms, bed compensation in use: mesh, height map offset 0.431, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
=== DDARing 0 ===
Scheduled moves 2731, completed 2731, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.4
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0, sync state 2
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000000
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== Filament sensors ===
Extruder 0 sensor: no filament
Extruder 1 sensor: no filament
Extruder 2 sensor: no filament
Extruder 3 sensor: no filament
=== CAN ===
Messages queued 2142023, received 10609283, lost 0, boc 0
Longest wait 4ms for reply type 6013, peak Tx sync delay 439, free buffers 50 (min 48), ts 646832/646831/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 213.14ms; fastest: 0.03ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 2 of 8
= Ethernet =
Interface state: active
Error counts: 0 0 0 1 0 0
Socket states: 5 2 2 2 2 0 0 0
=== Multicast handler ===
Responder is inactive, messages received 0, responses 0


after reset:
m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.5.0-beta.4 (2023-06-08 23:41:30) running on Duet 3 MB6HC v1.01 (standalone mode)
Board ID: 08DJM-9P63L-DJ3T0-6J9F0-3SN6L-TU37A
Used output buffers: 3 of 40 (38 max)
=== RTOS ===
Static ram: 155012
Dynamic ram: 123936 of which 0 recycled
Never used RAM 63276, free system stack 117 words
Tasks: NETWORK(1,ready,39.1%,182) ETHERNET(5,nWait,0.1%,392) HEAT(3,nWait,0.0%,323) Move(4,nWait,0.0%,214) CanReceiv(6,nWait,0.1%,769) CanSender(5,nWait,0.0%,326) CanClock(7,delaying,0.0%,349) TMC(4,nWait,8.4%,59) MAIN(1,running,52.2%,137) IDLE(0,ready,0.0%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 35:58:35 ago, cause: power up
Last software reset at 2023-11-04 14:45, reason: User, Gcodes spinning, available RAM 62236, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
MCU temperature: min 30.8, current 31.0, max 31.2
Supply voltage: min 23.7, current 23.8, max 23.8, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/284/284, gc cycles 0
Events: 1 queued, 1 completed
Driver 0: standstill, SG min n/a, mspos 920, reads 38133, writes 0 timeouts 0
Driver 1: standstill, SG min n/a, mspos 736, reads 38133, writes 0 timeouts 0
Driver 2: standstill, SG min n/a, mspos 568, reads 38133, writes 0 timeouts 0
Driver 3: standstill, SG min n/a, mspos 744, reads 38134, writes 0 timeouts 0
Driver 4: standstill, SG min n/a, mspos 344, reads 38134, writes 0 timeouts 0
Driver 5: standstill, SG min n/a, mspos 120, reads 38134, writes 0 timeouts 0
Date/time: 2023-11-06 02:44:23
Slowest loop: 10.23ms; fastest: 0.08ms
=== Storage ===
Free file entries: 20
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 4.7ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 38, maxWait 0ms, bed compensation in use: mesh, height map offset 0.431, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
=== DDARing 0 ===
Scheduled moves 2731, completed 2731, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.4
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0, sync state 2
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000000
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== Filament sensors ===
Extruder 0 sensor: no filament
Extruder 1 sensor: no filament
Extruder 2 sensor: no filament
Extruder 3 sensor: no filament
=== CAN ===
Messages queued 1345, received 12239, lost 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 274, free buffers 50 (min 50), ts 747/747/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 8.26ms; fastest: 0.03ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 2 of 8
= Ethernet =
Interface state: active
Error counts: 0 0 0 0 0 0
Socket states: 2 2 2 2 2 0 0 0
=== Multicast handler ===
Responder is inactive, messages received 0, responses 0

--------------------------------------------------------------------------------
before reset:
m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.5.0-rc.1 (2023-08-31 16:16:15) running on Duet WiFi 1.02 or later
Board ID: 08DGM-917DA-G4MS8-6JKD0-3SD6M-KTSRA
Used output buffers: 1 of 26 (26 max)
=== RTOS ===
Static ram: 23076
Dynamic ram: 75564 of which 0 recycled
Never used RAM 11648, free system stack 184 words
Tasks: NETWORK(1,ready,116.3%,218) HEAT(3,nWait,29.8%,329) Move(4,nWait,1.4%,364) MAIN(1,running,367.4%,747) IDLE(0,ready,7.0%,29), total 522.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 147:55:16 ago, cause: software
Last software reset at 2023-10-30 22:51, reason: User, Gcodes spinning, available RAM 10968, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x04
MCU temperature: min 24.6, current 26.1, max 34.2
Supply voltage: min 23.3, current 24.3, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/1, heap memory allocated/used/recyclable 2048/32/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min n/a
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min n/a
Driver 5: 
Driver 6: 
Driver 7: 
Driver 8: 
Driver 9: 
Driver 10: 
Driver 11: 
Date/time: 2023-11-06 02:46:29
Cache data hit count 4294967295
Slowest loop: 76.04ms; fastest: 0.20ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 52.5ms, write time 0.0ms, max retries 1
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters 2 -1 -1 -1, ordering errs 0
Heater 2 is on, I-accum = 0.0
=== GCodes ===
Movement locks held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Q0 segments left 0
Code queue 0 is empty
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 21.17ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 2 of 8
=== WiFi ===
Interface state: active
Module is connected to access point 
Failed messages: pending 0, notrdy 0, noresp 0
Firmware version 1.26
MAC address b4:e6:2d:52:ef:1f
Module reset reason: Turned on by main processor, Vcc 3.43, flash size 4194304, free heap 24720
WiFi IP address 192.168.1.161
Signal strength -60dBm, channel 0, mode 802.11n, reconnections 0
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0
2023-11-04, 11:28:11 p.m. 	Connected to 192.168.1.161

after reset:

m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.5.0-rc.1 (2023-08-31 16:16:15) running on Duet WiFi 1.02 or later
Board ID: 08DGM-917DA-G4MS8-6JKD0-3SD6M-KTSRA
Used output buffers: 1 of 26 (26 max)
=== RTOS ===
Static ram: 23076
Dynamic ram: 75564 of which 0 recycled
Never used RAM 11648, free system stack 184 words
Tasks: NETWORK(1,ready,14.7%,218) HEAT(3,nWait,0.1%,329) Move(4,nWait,0.0%,364) MAIN(1,running,85.2%,747) IDLE(0,ready,0.0%,29), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 147:57:45 ago, cause: software
Last software reset at 2023-10-30 22:51, reason: User, Gcodes spinning, available RAM 10968, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x04
MCU temperature: min 25.7, current 26.0, max 26.4
Supply voltage: min 24.2, current 24.3, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/1, heap memory allocated/used/recyclable 2048/32/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min n/a
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min n/a
Driver 5: 
Driver 6: 
Driver 7: 
Driver 8: 
Driver 9: 
Driver 10: 
Driver 11: 
Date/time: 2023-11-06 02:48:58
Cache data hit count 4294967295
Slowest loop: 11.00ms; fastest: 0.20ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.2ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters 2 -1 -1 -1, ordering errs 0
Heater 2 is on, I-accum = 0.0
=== GCodes ===
Movement locks held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Q0 segments left 0
Code queue 0 is empty
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 101.91ms; fastest: 0.08ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 2 of 8
=== WiFi ===
Interface state: active
Module is connected to access point 
Failed messages: pending 0, notrdy 0, noresp 2
Firmware version 1.26
MAC address b4:e6:2d:52:ef:1f
Module reset reason: Turned on by main processor, Vcc 3.43, flash size 4194304, free heap 26296
WiFi IP address 192.168.1.161
Signal strength -60dBm, channel 0, mode 802.11n, reconnections 0
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0