1/2/2024, 3:11:48 PM: Connected to 10.0.0.200


1/2/2024, 3:14:57 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6XD version 3.5.0-rc.2 (2023-12-14 10:33:00) running on Duet 3 MB6XD v1.01 or later (standalone mode)
Board ID: 0JD2M-999AL-D25S0-7J9DA-3SJ6S-T43V2
Used output buffers: 1 of 40 (27 max)
=== RTOS ===
Static ram: 153284
Dynamic ram: 117268 of which 0 recycled
Never used RAM 72584, free system stack 198 words
Tasks: NETWORK(1,ready,156.9%,182) ETHERNET(5,nWait,0.1%,317) HEAT(3,nWait,0.1%,363) Move(4,nWait,0.0%,324) CanReceiv(6,nWait,0.0%,797) CanSender(5,nWait,0.0%,334) CanClock(7,delaying,0.1%,342) MAIN(1,running,309.2%,444) IDLE(0,ready,4.2%,30), total 470.7%
Owned mutexes:
=== Platform ===
Last reset 06:47:31 ago, cause: power up
Last software reset at 2023-12-29 19:10, reason: User, Gcodes spinning, available RAM 72856, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
MCU temperature: min 26.7, current 43.2, max 44.9
Supply voltage: min 1.0, current 24.3, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 0.1, current 12.2, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/12/12, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: ok
Driver 1: ok
Driver 2: ok
Driver 3: ok
Driver 4: ok
Driver 5: ok
Date/time: 2024-01-02 15:14:56
Slowest loop: 13.14ms; fastest: 0.07ms
=== Storage ===
Free file entries: 20
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 2.4ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000000
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== CAN ===
Messages queued 122313, received 2013, lost 0, errs 119097786, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 41498, free buffers 50 (min 49), ts 122256/464/0
Tx timeouts 0,0,121791,53,0,0 last cancelled message type 30 dest 127
=== Network ===
Slowest loop: 7.56ms; fastest: 0.03ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
= Ethernet =
Interface state: active
Error counts: 0 0 0 0 0 0
Socket states: 5 2 2 2 2 0 0 0
=== Multicast handler ===
Responder is inactive, messages received 0, responses 0



1/2/2024, 3:15:13 PM: M122 B1: Duet EXP3HC rev 1.02 or later firmware version 3.5.0-rc.2 (2
CAN response timeout: board 1, req type 6024, RID 54


1/2/2024, 3:15:17 PM: M122 B2: Diagnostics for board 2:
Duet EXP3HC rev 1.02 or later firmware version 3.5.0-rc.2 (2023-12-14 08:56:47)
Bootloader ID: SAME5x bootloader version 2.4 (2021-12-10)
All averaging filters OK
Never used RAM 156976, free system stack 202 words
Tasks: Move(3,nWait,0.0%,182) HEAT(2,nWait,0.0%,120) CanAsync(5,nWait,0.0%,67) CanRecv(3,nWait,0.0%,80) CanClock(5,nWait,0.0%,70) TMC(2,nWait,5.7%,103) MAIN(1,running,93.1%,424) IDLE(0,ready,0.0%,39) AIN(2,delaying,1.1%,263), total 100.0%
Last reset 00:01:53 ago, cause: power up
Last software reset data not available
Driver 0: pos 0, 80.0 steps/mm, standstill, SG min 0, mspos 8, reads 50544, writes 11 timeouts 0, steps req 0 done 0
Driver 1: pos 0, 80.0 steps/mm, standstill, SG min 0, mspos 8, reads 50545, writes 11 timeouts 0, steps req 0 done 0
Driver 2: pos 0, 80.0 steps/mm, standstill, SG min 0, mspos 8, reads 50545, writes 11 timeouts 0, steps req 0 done 0
Moves scheduled 0, completed 0, in progress 0, hiccups 0, segs 0, step errors 0, maxLate 0 maxPrep 0, maxOverdue 0, maxInc 0, mcErrs 0, gcmErrs 0, ebfmin 0.00 max 0.00
Peak sync jitter -5/5, peak Rx sync delay 180, resyncs 0/0, no timer interrupt scheduled
VIN voltage: min 24.5, current 24.5, max 24.5
V12 voltage: min 12.3, current 12.3, max 12.4
MCU temperature: min 23.4C, current 28.0C, max 28.2C
Last sensors broadcast 0x00000000 found 0 70 ticks ago, 0 ordering errs, loop time 0
CAN messages queued 934, send timeouts 0, received 578, lost 0, errs 21060, boc 2, free buffers 38, min 38, error reg ff7800
dup 0, oos 0/0/0/0, bm 0, wbm 0, rxMotionDelay 0



1/2/2024, 3:15:21 PM: M122 B3: Diagnostics for board 3:
Duet EXP3HC rev 1.02 or later firmware version 3.5.0-rc.2 (2023-12-14 08:56:47)
Bootloader ID: SAME5x bootloader version 2.4 (2021-12-10)
All averaging filters OK
Never used RAM 156976, free system stack 202 words
Tasks: Move(3,nWait,0.0%,182) HEAT(2,nWait,0.0%,122) CanAsync(5,nWait,0.0%,67) CanRecv(3,nWait,0.0%,80) CanClock(5,nWait,0.0%,70) TMC(2,nWait,5.7%,103) MAIN(1,running,93.1%,436) IDLE(0,ready,0.0%,39) AIN(2,delaying,1.1%,263), total 100.0%
Last reset 00:01:57 ago, cause: power up
Last software reset data not available
Driver 0: pos 0, 80.0 steps/mm, standstill, SG min 0, mspos 8, reads 253, writes 11 timeouts 0, steps req 0 done 0
Driver 1: pos 0, 80.0 steps/mm, standstill, SG min 0, mspos 8, reads 254, writes 11 timeouts 0, steps req 0 done 0
Driver 2: pos 0, 80.0 steps/mm, standstill, SG min 0, mspos 8, reads 255, writes 11 timeouts 0, steps req 0 done 0
Moves scheduled 0, completed 0, in progress 0, hiccups 0, segs 0, step errors 0, maxLate 0 maxPrep 0, maxOverdue 0, maxInc 0, mcErrs 0, gcmErrs 0, ebfmin 0.00 max 0.00
Peak sync jitter -3/6, peak Rx sync delay 183, resyncs 0/0, no timer interrupt scheduled
VIN voltage: min 21.5, current 24.5, max 24.6
V12 voltage: min 12.3, current 12.3, max 12.4
MCU temperature: min 23.4C, current 27.6C, max 27.9C
Last sensors broadcast 0x00000000 found 0 227 ticks ago, 0 ordering errs, loop time 0
CAN messages queued 964, send timeouts 0, received 596, lost 0, errs 20996, boc 10, free buffers 38, min 38, error reg ff7622
dup 0, oos 0/0/0/0, bm 0, wbm 0, rxMotionDelay 0