M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.4.6 (2023-07-21 14:11:38) running on Duet 3 MB6HC v1.01 (SBC mode)
Board ID: 0JD2M-999AL-D25S4-7J9D8-3SN6R-KN1R3
Used output buffers: 1 of 40 (12 max)
=== RTOS ===
Static ram: 153252
Dynamic ram: 66752 of which 512 recycled
Never used RAM 130156, free system stack 216 words
Tasks: SBC(ready,0.5%,478) HEAT(notifyWait,0.0%,321) Move(notifyWait,0.0%,352) CanReceiv(notifyWait,0.0%,943) CanSender(notifyWait,0.0%,335) CanClock(delaying,0.0%,343) TMC(notifyWait,6.8%,92) MAIN(running,92.4%,975) IDLE(ready,0.3%,30), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:04:02 ago, cause: power up
Last software reset at 2024-02-08 03:15, reason: User, GCodes spinning, available RAM 130156, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 640
MCU temperature: min 18.5, current 31.5, max 31.6
Supply voltage: min 0.1, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 0.1, current 12.2, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 0, mspos 8, reads 52763, writes 11 timeouts 0
Driver 1: standstill, SG min 0, mspos 8, reads 52763, writes 11 timeouts 0
Driver 2: standstill, SG min 0, mspos 8, reads 52763, writes 11 timeouts 0
Driver 3: standstill, SG min 0, mspos 8, reads 52763, writes 11 timeouts 0
Driver 4: standstill, SG min 0, mspos 8, reads 52763, writes 11 timeouts 0
Driver 5: standstill, SG min 0, mspos 8, reads 52764, writes 11 timeouts 0
Date/time: 2024-02-10 02:32:48
Slowest loop: 1.26ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Filament sensors ===
Extruder 0 sensor: ok
=== CAN ===
Messages queued 2095, received 0, lost 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 50 (min 50), ts 1211/0/0
Tx timeouts 0,0,1210,0,0,883 last cancelled message type 30 dest 127
=== SBC interface ===
Transfer state: 5, failed transfers: 0, checksum errors: 0
RX/TX seq numbers: 9720/9720
SPI underruns 0, overruns 0
State: 5, disconnects: 0, timeouts: 0 total, 0 by SBC, IAP RAM available 0x2ab5c
Buffer RX/TX: 0/0-0, open files: 0
=== Duet Control Server ===
Duet Control Server v3.4.6
Code buffer space: 4096
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 0
Full transfers per second: 0.06, max time between full transfers: 148.7ms, max pin wait times: 32.8ms/1.1ms
Codes per second: 0.00
Maximum length of RX/TX data transfers: 3120/796