m122 === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.6.0-alpha.2+3 (2024-07-17 20:03:21) running on Duet WiFi 1.02 or later Board ID: 0JD2M-9F8TA-GJ4TD-6J1D6-3SD6P-16PG6 Used output buffers: 1 of 26 (11 max) === RTOS === Static ram: 23368 Dynamic ram: 66468 of which 0 recycled Never used RAM 31092, free system stack 182 words Tasks: NETWORK(1,ready,5.7%,429) HEAT(3,nWait 5,0.0%,328) Move(4,nWait 5,0.0%,359) MAIN(1,running,82.0%,740) IDLE(0,ready,12.3%,29), total 100.0% Owned mutexes: USB(MAIN) === Platform === Last reset 00:00:07 ago, cause: software Last software reset at 2024-07-19 19:46, reason: User, Gcodes spinning, available RAM 13680, slot 2 Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a Error status: 0x00 Aux0 errors 0,0,0 MCU temperature: min 32.4, current 32.8, max 33.2 Supply voltage: min 24.9, current 25.0, max 25.2, under voltage events: 0, over voltage events: 0, power good: yes Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0 Events: 0 queued, 0 completed Date/time: 1970-01-01 00:00:00 Slowest loop: 6.41ms; fastest: 0.19ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Storage === Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest read time 0.7ms, write time 0.0ms, max retries 0 === Move === Segments created 0, maxWait 0ms, bed comp in use: none, height map offset 0.000, hiccups added 0 (0.00ms), max steps late 0, ebfmin 0.00, ebfmax 0.00, mcet 0.000 Pos req/act/dcf: 0.00/0/0.00 0.00/0/0.00 0.00/0/0.00 no step interrupt scheduled === DDARing 0 === Scheduled moves 0, completed 0, LaErrors 0, Underruns [0, 0, 0] Driver 0: standstill, SG min n/a Driver 1: standstill, SG min n/a Driver 2: standstill, SG min n/a Driver 3: standstill, SG min n/a Driver 4: standstill, SG min n/a Driver 5: Driver 6: Driver 7: Driver 8: Driver 9: Driver 10: Driver 11: === Heat === Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0 Heater 1 is on, I-accum = 0.0 === GCodes === Movement locks held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is ready with "m122" in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 Daemon is idle in state(s) 0 Autopause is idle in state(s) 0 Q0 segments left 0 Code queue 0 is empty === Network === Slowest loop: 0.91ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) HTTP sessions: 0 of 8 === WiFi === Interface state: changingMode Module is trying to connect Failed messages: pending 0, notrdy 0, noresp 0 Firmware version 2.1.0 MAC address 00:00:00:00:00:00 Module reset reason: Power up, Vcc 3.40, flash size 2097152, free heap 47524 Clock register 00002002 Socket states: 0 0 0 0 0 0 0 0 ok WiFi module is connected to access point C3D 2.4GHz, IP address 192.168.1.197 m111 p4 d1 b2048 Debugging enabled for modules: Move(4 - 0x1) Debugging disabled for modules: Platform(0) Network(1) Webserver(2) Gcodes(3) Heat(5) Kinematics(6) InputShaping(7) unused(8) PrintMonitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13) WiFi(14) Display(15) SbcInterface(16) CAN(17) Expansion(18) Leadscrew adjustments made: -0.348 -0.328, points used 2, (mean, deviation) before (-0.338, 0.009) after (-0.000, 0.000) Leadscrew adjustments made: 0.004 0.004, points used 2, (mean, deviation) before (0.004, 0.000) after (-0.000, 0.000) Warning: the height map has a substantial Z offset. Suggest use Z-probe to establish Z=0 datum, then re-probe the mesh. 25 points probed, min error 0.269, max error 0.490, mean 0.388, deviation 0.062 Height map saved to file 0:/sys/heightmap.csv Done printing file Finished printing file 0:/gcodes/ultraspeed half print.gcode, print time was 0h 21m m122 === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.6.0-alpha.2+3 (2024-07-17 20:03:21) running on Duet WiFi 1.02 or later Board ID: 0JD2M-9F8TA-GJ4TD-6J1D6-3SD6P-16PG6 Used output buffers: 6 of 26 (23 max) === RTOS === Static ram: 23368 Dynamic ram: 68644 of which 0 recycled Never used RAM 3768, free system stack 102 words Tasks: NETWORK(1,ready,21.7%,195) HEAT(3,nWait 5,0.1%,309) Move(4,nWait 5,5.8%,272) MAIN(1,running,72.3%,724) IDLE(0,ready,0.1%,29), total 100.0% Owned mutexes: WiFi(NETWORK) USB(MAIN) === Platform === Last reset 00:25:47 ago, cause: software Last software reset at 2024-07-19 19:46, reason: User, Gcodes spinning, available RAM 13680, slot 2 Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a Error status: 0x00 Aux0 errors 0,0,0 MCU temperature: min 30.1, current 30.4, max 33.3 Supply voltage: min 24.5, current 24.9, max 25.4, under voltage events: 0, over voltage events: 0, power good: yes Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/168/168, gc cycles 0 Events: 0 queued, 0 completed Date/time: 2024-07-19 20:12:02 Slowest loop: 317.05ms; fastest: 0.13ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Storage === Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest read time 16.9ms, write time 2.5ms, max retries 0 === Move === Segments created 929, maxWait 179263ms, bed comp in use: mesh, height map offset 0.000, hiccups added 119 (3.55ms), max steps late 1, ebfmin 0.00, ebfmax 0.00, mcet 0.100 Pos req/act/dcf: 29200.00/29199/1.00 -28400.00/-28400/-0.01 320230.00/320229/1.00 no step interrupt scheduled === DDARing 0 === Scheduled moves 77846, completed 77846, LaErrors 0, Underruns [87, 0, 0] Driver 0: standstill, SG min 0 Driver 1: standstill, SG min 0 Driver 2: standstill, SG min 0 Driver 3: standstill, SG min 0 Driver 4: standstill, SG min 0 Driver 5: Driver 6: Driver 7: Driver 8: Driver 9: Driver 10: Driver 11: === Heat === Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0 Heater 0 is on, I-accum = 0.1 === GCodes === Movement locks held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is ready with "m122" in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 Daemon is idle in state(s) 0 Autopause is idle in state(s) 0 Q0 segments left 0 Code queue 0 is empty === Network === Slowest loop: 222.55ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) HTTP sessions: 2 of 8 === WiFi === Interface state: active Module is connected to access point Failed messages: pending 0, notrdy 0, noresp 0 Firmware version 2.1.0 MAC address a4:e5:7c:03:da:81 Module reset reason: Power up, Vcc 3.40, flash size 2097152, free heap 37868 WiFi IP address 192.168.1.197 Signal strength -49dBm, channel 11, mode 802.11n, reconnections 0 Clock register 00002002 Socket states: 0 0 0 0 0 0 0 0 ok