m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6XD version 3.6.0-beta.2 (2024-11-12 08:13:23) running on Duet 3 MB6XD v1.01 (SBC mode)
Board ID: 0JD2M-999AL-D25S0-7J9FD-3SJ6S-143B2
Used output buffers: 1 of 40 (29 max)
=== RTOS ===
Static ram: 133820
Dynamic ram: 97084 of which 24 recycled
Never used RAM 97768, free system stack 204 words
Tasks: SBC(2,ready,1.5%,826) HEAT(3,nWait 6,0.0%,369) Move(4,nWait 6,0.0%,333) CanReceiv(6,nWait 1,0.1%,794) CanSender(5,nWait 7,0.0%,334) CanClock(7,delaying,0.0%,353) MAIN(2,running,88.2%,440) IDLE(0,ready,10.1%,29) USBD(3,blocked,0.0%,144), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:00:05 ago, cause: software
Last software reset at 2024-12-18 08:40, reason: User, Gcodes spinning, available RAM 94696, slot 0
Software reset code 0x2003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
MCU temperature: min 35.9, current 36.2, max 36.5
Supply voltage: min 23.9, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.2, current 12.3, max 12.3, under voltage events: 0
Heap OK, handles allocated/used 99/2, heap memory allocated/used/recyclable 2048/84/44, gc cycles 0
Events: 0 queued, 0 completed
Date/time: 2024-12-18 08:40:59
Slowest loop: 35.77ms; fastest: 0.00ms
USB interrupts 3
=== Storage ===
Free file entries: 20
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
Segments created 0, maxWait 0ms, bed comp in use: none, height map offset 0.000, hiccups added 0/0 (0.00/0.00ms), max steps late 0, ebfmin 0.00, ebfmax 0.00
Pos req/act/dcf: 0.00/0/0.00 0.00/0/0.00 0.00/0/0.00 0.00/0/0.00 0.00/0/0.00 0.00/0/0.00 0.00/0/0.00
no step interrupt scheduled
Driver 0: ok
Driver 1: ok
Driver 2: ok
Driver 3: ok
Driver 4: ok
Driver 5: ok
=== DDARing 0 ===
Scheduled moves 0, completed 0, LaErrors 0, Underruns [0, 0, 0]
=== DDARing 1 ===
Scheduled moves 0, completed 0, LaErrors 0, Underruns [0, 0, 0]
=== Heat ===
Bed heaters 2 3 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters 4 5 6 -1 -1 -1 -1 -1, ordering errs 0=== GCodes ===
Movement locks held by null, null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0 0, running macro
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000000
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== CAN ===
Messages queued 170, received 583, lost 0, ignored 0, errs 1, boc 0
Longest wait 2ms for reply type 6042, peak Tx sync delay 360, free buffers 50 (min 49), ts 27/26/0
Tx timeouts 0,0,0,0,0,0
=== SBC interface ===
Transfer state: 5, failed transfers: 1, checksum errors: 0
RX/TX seq numbers: 1844/224
SPI underruns 0, overruns 0
State: 5, disconnects: 0, timeouts: 0 total, 0 by SBC, IAP RAM available 0x2962c
Buffer RX/TX: 0/0-0, open files: 0
=== Duet Control Server ===
Duet Control Server version 3.6.0-beta.2 (2024-11-14 11:02:38, 64-bit)
HTTP+Executed:
> Executing M122
Trigger+ProcessInternally:
>> Macro config.g: Executing echo > "/sys/startup-z-pos.g" "" (5 more codes pending)
Trigger:
Buffered code: M710 T2300
Buffered code: M710 H2 S2 P420 ;bed
Buffered code: M710 H3 S2 P800
Buffered code: M710 H4 S1 P1900 ;chamber
Buffered code: M710 H5 S3 P320 ;filament chambers
Buffered code: M710 H6 S3 P320
Buffered code: M950 J14 C"^10.io0.in" ; Left Tray - Upper left sensor	
Buffered code: M950 J15 C"^10.io3.in" ; Left Tray - Upper right sensor
Buffered code: M950 J16 C"^!20.io0.in" ; Extruder 0 sensor
Buffered code: M591 D0 P3 C"20.io1.in" S1 A0 L31.78 E10 R20:180 ; Extruder 0 filament monitor
Buffered code: M591 D4 P1 C"^10.io2.in" S1 ; simple sensor (high signal when filament present) Left Tray - Lower left sensor
Buffered code: M591 D5 P1 C"^10.io1.in" S1 ; simple sensor (high signal when filament present) Left Tray - Lower right sensor
Buffered code: M950 J19 C"^11.io0.in" ; Right Tray - Upper left sensor
Buffered code: M950 J20 C"^11.io3.in" ; Right Tray - Upper right sensor
Buffered code: M950 J21 C"^!21.io0.in" ; Extruder 1 sensor
Buffered code: M591 D1 P3 C"21.io1.in" S1 A0 L25.68 E10 R20:180 ; Extruder 1 filament monitor
Buffered code: M591 D2 P1 C"^11.io2.in" S1 ; simple sensor (high signal when filament present)
Buffered code: M591 D3 P1 C"^11.io1.in" S1 ; simple sensor (high signal when filament present)
Buffered code: M98 P"t-offsets.g"
Buffered code: M98 P"startup-z-offset.g"
Buffered code: M98 P"startup-xy-offset.g"
Buffered code: M98 P"startup-z-pos.g"
Buffered codes: 1268 bytes total
>> Doing macro config.g, started by system
>> Number of flush requests: 1
Code buffer space: 1368
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 0
Full transfers per second: 17.36, max time between full transfers: 530.1ms, max pin wait times: 499.9ms/247.6ms
Codes per second: 10.98
Maximum length of RX/TX data transfers: 8176/1864