12/11/2024, 3:35:21 AM: Connected to 192.168.1.15
12/11/2024, 3:35:33 AM: m906: Motor current (mA) - X:5000, Y:4000, Z:2500, E, idle factor 30%
12/11/2024, 3:35:42 AM: m913: Motor current % of normal - X:100, Y:100, Z:100, E
12/11/2024, 3:36:07 AM: m98 P"config.g": HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: Fan number 2 not found
12/11/2024, 3:36:19 AM: m122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-956BA-NA3TN-6JKDL-3SS6P-9T9LV
Used output buffers: 1 of 40 (12 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 91380 of which 20 recycled
Never used RAM 111888, free system stack 206 words
Tasks: NETWORK(ready,30.4%,254) ETHERNET(notifyWait,0.2%,124) HEAT(delaying,0.0%,405) Move(notifyWait,0.0%,302) CanReceiv(notifyWait,0.0%,944) CanSender(notifyWait,0.0%,374) CanClock(delaying,0.0%,333) TMC(notifyWait,7.5%,93) MAIN(running,61.7%,1226) IDLE(ready,0.1%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:01:49 ago, cause: software
Last software reset at 2024-12-11 03:34, reason: User, GCodes spinning, available RAM 111888, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 130
MCU temperature: min 23.8, current 24.3, max 24.4
Supply voltage: min 23.9, current 23.9, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.2, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, reads 18453, writes 17 timeouts 0, SG min/max 0/0
Driver 1: position 0, standstill, reads 18454, writes 17 timeouts 0, SG min/max 0/0
Driver 2: position 0, standstill, reads 18454, writes 17 timeouts 0, SG min/max 0/0
Driver 3: position 0, standstill, reads 18454, writes 17 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 18460, writes 11 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 18460, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2024-12-11 03:36:18
Slowest loop: 3.90ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 0.9ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 547, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 49 (min 49), ts 547/0/0
Tx timeouts 0,0,546,0,0,0 last cancelled message type 30 dest 127

=== Network ===
Slowest loop: 3.90ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 2 2 2 2 0 0 0