# generated by PrusaSlicer 2.9.0 on 2025-02-10 at 06:04:22 UTC

[print:D600Pro V1.1 1.0noz]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 3
bottom_solid_min_thickness = 0
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 150
brim_separation = 0
brim_type = outer_and_inner
brim_width = 10
compatible_printers = 
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0.1
enable_dynamic_overhang_speeds = 0
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 0
external_perimeter_extrusion_width = 1.25
external_perimeter_speed = 100%
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 1.25
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 0
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 1.25
first_layer_height = 0.4
first_layer_speed = 50%
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 30
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 0
infill_anchor = 600%
infill_anchor_max = 15
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 1.25
infill_first = 0
infill_overlap = 20%
infill_speed = 150
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.4
max_print_speed = 150
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 70
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 0
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhang_speed_0 = 15
overhang_speed_1 = 15
overhang_speed_2 = 20
overhang_speed_3 = 25
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 1.25
perimeter_generator = arachne
perimeter_speed = 40
perimeters = 3
post_process = 
print_settings_id = 
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 6
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 0
seam_position = aligned
single_extruder_multi_material_priming = 1
skirt_distance = 6
skirt_height = 1
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 100%
solid_infill_acceleration = 0
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 1.25
solid_infill_speed = 150
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 1.25
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 2
support_material_interface_pattern = rectilinear
support_material_interface_spacing = 0.6
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 5
support_material_speed = 120
support_material_style = organic
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 1
support_material_xy_spacing = 50%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 3.8
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 5
support_tree_branch_distance = 3
support_tree_tip_diameter = 2
support_tree_top_rate = 15%
thick_bridges = 1
thin_walls = 1
top_fill_pattern = monotonic
top_infill_extrusion_width = 1.25
top_one_perimeter_type = none
top_solid_infill_acceleration = 0
top_solid_infill_speed = 40
top_solid_layers = 3
top_solid_min_thickness = 0
travel_acceleration = 0
travel_speed = 300
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[filament:D600Pro ASA]
bed_temperature = 125
bridge_fan_speed = 100
chamber_minimal_temperature = 60
chamber_temperature = 60
compatible_printers = 
compatible_printers_condition = printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1)
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 1
enable_dynamic_fan_speeds = 0
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.93
fan_always_on = 1
fan_below_layer_time = 180
filament_abrasive = 0
filament_colour = #808080
filament_cooling_final_speed = 2
filament_cooling_initial_speed = 3
filament_cooling_moves = 1
filament_cost = 42.69
filament_density = 1.07
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 14
filament_loading_speed_start = 19
filament_max_volumetric_speed = 70
filament_minimal_purge_on_wipe_tower = 0
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = ""
filament_shrinkage_compensation_xy = 0.5%
filament_shrinkage_compensation_z = 0.5%
filament_soluble = 0
filament_spool_weight = 201
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = ASA
filament_unload_time = 0
filament_unloading_speed = 20
filament_unloading_speed_start = 100
filament_vendor = Prusa Polymers
filament_wipe = nil
first_layer_bed_temperature = 125
first_layer_temperature = 260
full_fan_speed_layer = 1
idle_temperature = nil
inherits = 
max_fan_speed = 95
min_fan_speed = 95
min_print_speed = 5
overhang_fan_speed_0 = 0
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 110
start_filament_gcode = "; Filament gcode\n"
temperature = 260

[printer:CreatBot D600 Pro modified control board]
autoemit_temperature_commands = 1
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,550x0,550x590,0x590
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n
between_objects_gcode = 
binary_gcode = 0
color_change_gcode = M600\nG1 E0.4 F1500 ; prime after color change
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "CreatBot PLA"
default_print_profile = Standard
deretract_speed = 0
end_gcode = G91            ;Switch to relative\nG1 Z15 F8000   ;Move z down 15mm\nG90            ;back to absolute\nG1 X0 Y0 F8000 ; home X axis\nM104 S0        ; Nozzle off\nM140 S75       ; Bed to 75c\nM141 S60       ; Chamber to 60c\nG4 S1000       ; Dwell for 1000 seconds\nM140 S45       ; bed to 45c\nM141 S45       ; chamber to 45c\nG4 S1000       ; Dwell for 1000 seconds\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107    ; turn off fan\nM6013 S0  ; turn off chamber\n\nM84 X Y E ; disable motors\nG90                         ;absolute positioning\nM117 Print finished.
extra_loading_move = -2
extruder_colour = #FF8000
extruder_offset = 0x0
gcode_flavor = reprapfirmware
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = ;AFTER_LAYER_CHANGE\n;G92 E0   ;zero the extruded length again\n;[layer_z]\n\n{if layer_num == 1 }\nM120 ; push state\nG91 ; relative XY\nM83 ; relative extruder\nG1 E-1 F200\nG1 Z5 F1000\nG4 S80 ; wait for hotend to stabilize after fan turns on\nG1 Z-5 F1000\nG1 E1 F200\nM121 ; pop state\n{ endif }
machine_limits_usage = emit_to_gcode
machine_max_acceleration_e = 40
machine_max_acceleration_extruding = 1500
machine_max_acceleration_retracting = 3000
machine_max_acceleration_travel = 2000,1250
machine_max_acceleration_x = 2000
machine_max_acceleration_y = 1000
machine_max_acceleration_z = 300
machine_max_feedrate_e = 100
machine_max_feedrate_x = 300
machine_max_feedrate_y = 300
machine_max_feedrate_z = 10
machine_max_jerk_e = 5
machine_max_jerk_x = 10
machine_max_jerk_y = 10
machine_max_jerk_z = 10
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
max_layer_height = 0.5
max_print_height = 475
min_layer_height = 0.05
multimaterial_purging = 140
nozzle_diameter = 1
nozzle_high_flow = 0
parking_pos_retraction = 92
pause_print_gcode = M0
prefer_clockwise_movements = 0
print_host = 
printer_model = D600_Pro
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_CreatBot\nPRINTER_MODEL_D600_Pro\nPRINTER_SERIES_F\n
printer_settings_id = 
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 8
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 0.7
retract_length_toolchange = 12
retract_lift = 2
retract_lift_above = 0.2
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 50
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = G90 ; use absolute coordinates\nT0  ;  select tool 0\nM106 S0 ; make sure the part fan is off\n\nM104 S[first_layer_temperature] T0  ;  set hotend temp\nM140 S[first_layer_bed_temperature] ; set bed temperature\nM191 S[chamber_temperature] ; set chamber temperature and wait for it to be reached\n\nM280 P0 S160 ; reset BLTouch\n\nM190 R[first_layer_bed_temperature] ; wait for bed temperature to be reached\nM109 R[first_layer_temperature] T0  ;  wait for hotend to reach temperature\n\nM120 ; push state\nG90 ; absolute XY\nM83 ; relative extruder\nG1 X0 Y0 Z5 F12000\nG1 X100 E25 F6000\nG1 E-5 F200\nM121 ; pop state\n\nG1 X300 Y10 Z10 F8000 ; move to our initial probe location\nG30 ; touch probe and set the Z location to the probe height\n\n; Edit to G29 S1 (IN THE GCODE, NOT THE SLICER) to use the previous height map.\n; Do that instead of commenting this out so it happens after the touch probe,\n; which is fast and not optional.\nG29 S0 ; do mesh bed leveling, save height map, and activate\nM376 H25; Bed compensation taper of 25mm\n\nM120 ; push state\nG90 ; absolute XY\nM83 ; relative extruder\nG1 X130 Y0 Z5 F12000\nG1 X230 E25 F1000\nM121 ; pop state\n
template_custom_gcode = 
thumbnails = 
thumbnails_format = PNG
toolchange_gcode = 
travel_lift_before_obstacle = 1
travel_max_lift = 2
travel_ramping_lift = 1
travel_slope = 60
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0

[presets]
print = D600Pro V1.1 1.0noz
sla_print = - default -
sla_material = - default -
printer = CreatBot D600 Pro modified control board
filament = D600Pro ASA