2/28/2025, 3:39:48 PM: : U and V axis are not homed, performing homing
2/28/2025, 3:39:52 PM: M98 P"config.g"
2/28/2025, 3:39:55 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6XD version 3.5.4 (2024-11-24 10:47:53) running on Duet 3 MB6XD v1.0 (SBC mode)
Board ID: 08DLM-956DA-M2NS4-6JTD6-3S86M-1B3GT
Used output buffers: 1 of 40 (26 max)
=== RTOS ===
Static ram: 153872
Dynamic ram: 94912 of which 264 recycled
Never used RAM 94016, free system stack 163 words
Tasks: SBC(2,ready,1.1%,791) HEAT(3,nWait 6,0.0%,323) Move(4,nWait 6,0.0%,211) CanReceiv(6,nWait 1,0.2%,771) CanSender(5,nWait 7,0.0%,329) CanClock(7,delaying,0.0%,348) MAIN(2,running,98.3%,126) IDLE(0,ready,0.4%,29), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 05:06:01 ago, cause: software
Last software reset at 2025-02-28 10:32, reason: User, Gcodes spinning, available RAM 94872, slot 2
Software reset code 0x6003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 43.3, current 43.5, max 44.0
Supply voltage: min 24.3, current 24.4, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.2, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 99/54, heap memory allocated/used/recyclable 2048/1088/144, gc cycles 59
Events: 2 queued, 2 completed
Driver 0: ok
Driver 1: ok
Driver 2: ok
Driver 3: ok
Driver 4: ok
Driver 5: ok
Date/time: 2025-02-28 15:38:36
Slowest loop: 31.21ms; fastest: 0.07ms
=== Storage ===
Free file entries: 20
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 3, maxWait 133757ms, bed compensation in use: none, height map offset 0.000, max steps late 0, min interval 0, bad calcs 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 50, completed 50, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters 1 -1 -1 -1, ordering errs 0
=== GCodes ===
Movement locks held by null, null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x20000003
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== CAN ===
Messages queued 1390, received 14232, lost 0, errs 0, boc 0
Longest wait 3ms for reply type 4012, peak Tx sync delay 152, free buffers 50 (min 48), ts 624/624/0
Tx timeouts 0,0,0,0,0,0
=== SBC interface ===
Transfer state: 5, failed transfers: 0, checksum errors: 0
RX/TX seq numbers: 59307/59307
SPI underruns 0, overruns 0
State: 5, disconnects: 0, timeouts: 0 total, 0 by SBC, IAP RAM available 0x25744
Buffer RX/TX: 0/0-0, open files: 0
=== Duet Control Server ===
Duet Control Server version 3.5.4 (2024-11-25 17:32:26, 64-bit)
HTTP+Executed:
> Executing M122
Code buffer space: 4096
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 0
Full transfers per second: 40.61, max time between full transfers: 36.1ms, max pin wait times: 28.7ms/0.3ms
Codes per second: 1.97
Maximum length of RX/TX data transfers: 6675/856