; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sat Apr 04 2020 19:27:02 GMT+0200 (Ora legale dell’Europa centrale)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"My Printer EUGENIO"                         ; set printer name

; Network
M552 P192.168.1.18 S1                              ; enable network and set IP address
M553 P255.255.255.0                                ; set netmask
M554 P192.168.1.254                                ; set gateway
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0 S0                                         ; physical drive 0 goes backwards
M569 P1 S0                                         ; physical drive 1 goes backwards
M569 P2 S0                                         ; physical drive 2 goes backwards
M569 P3 S0                                         ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X32 Y32 I0                                    ; configure microstepping without interpolation
M350 Z16 E16 I1                                    ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z4000.00 E420.00               ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X1300 Y1300 Z800 E800 I30                     ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X-10 Y-10 Z0 S1                               ; set axis minima
M208 X310 Y310 Z450 S0                             ; set axis maxima

; Endstops
M574 X1 Y1 Z1 S0                                   ; set active low and disabled endstops

; Z-Probe
M558 P0 H5 F120 T6000                              ; disable Z probe but set dive height, probe speed and travel speed
M557 X20:290 Y10:290 S20                           ; define mesh grid

; Heaters
M307 H0 B0 S1.00                                   ; disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 1
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1                             ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                          ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 S"E0" D0 H1 F0                             ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings
M92 E 95.245

; Miscellaneous
M911 S18 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss