; Configuration file for RepRapFirmware on Duet 2 Ethernet
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.5.12 on Wed May 28 2025 10:35:39 GMT+0200 (Ora legale dell’Europa centrale)

; General
G90 ; absolute coordinates
M83 ; relative extruder moves
M550 P"BAY PRINT EUGENIO" ; set hostname
M911 S19.8 R22 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

; Accessories
M575 P1 S0 B57600 ; configure PanelDue support

; Network
M552 P192.168.1.18 S1 ; configure Ethernet adapter
M553 P255.255.255.0 ; set netmask
M554 P192.168.1.254 ; set gateway
M586 P0 S1 ; configure HTTP

; Smart Drivers
M569 P0 S0 D2 ; driver 0 goes backwards (X axis)
M569 P1 S0 D2 ; driver 1 goes backwards (Y axis)
M569 P2 S0 D2 ; driver 2 goes backwards (Z axis)
M569 P3 S1 D2 ; driver 3 goes forwards (extruder 0)

; Motor Idle Current Reduction
M906 I30 ; set motor current idle factor
M84 S30 ; set motor current idle timeout

; Axes
M584 X0 Y1 Z2 ; set axis mapping
M350 X16 Y16 Z16 I1 ; configure microstepping with interpolation
M906 X1300 Y1300 Z800 ; set axis driver currents
M92 X80 Y80 Z4000 ; configure steps per mm
M208 X0:310 Y0:310 Z0:450 ; set minimum and maximum axis limits
M566 X900 Y900 Z12 ; set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z180 ; set maximum speeds (mm/min)
M201 X500 Y500 Z20 ; set accelerations (mm/s^2)

; Extruders
M584 E3 ; set extruder mapping
M350 E16 I1 ; configure microstepping with interpolation
M906 E800 ; set extruder driver currents
M92 E95.245 ; configure steps per mm
M566 E120 ; set maximum instantaneous speed changes (mm/min)
M203 E1200 ; set maximum speeds (mm/min)
M201 E250 ; set accelerations (mm/s^2)

; Kinematics
M669 K0 ; configure Cartesian kinematics

; Probes
M558 K0 P9 C"^zprobe.in" H5 F120 T6000 ; configure BLTouch probe via slot #0
G31 P500 X0 Y0 Z3.65 ; set Z probe trigger value, offset and trigger height
M950 S0 C"exp.heater3" ; create servo #0 for BLtouch

; Endstops
M574 X1 P"xstop" S1 ; configure X axis endstop
M574 Y1 P"ystop" S1 ; configure Y axis endstop
M574 Z1 S2 ; configure Z axis endstop

; Mesh Bed Compensation
M557 X5:270 Y25:285 S40:40 ; define grid for mesh bed compensation

; Sensors
M308 S0 P"bedtemp" Y"thermistor" A"Heated Bed" T100000 B4138 ; configure sensor #0
M308 S1 P"e0temp" Y"thermistor" A"Nozzle" T100000 B4664 C6.236032e-8 ; configure sensor #1

; Heaters
M950 H0 C"bedheat" T0 ; create heater #0
M143 H0 P0 T0 C0 S120 A0 ; configure heater monitor #0 for heater #0
M307 H0 R2.43 D5.5 E1.35 K0.56 B0 ; configure model of heater #0
M950 H1 C"e0heat" T1 ; create heater #1
M143 H1 P0 T1 C0 S290 A0 ; configure heater monitor #0 for heater #1
M307 H1 R2.43 D5.5 E1.35 K0.56 B0 ; configure model of heater #1

; Heated beds
M140 P0 H0 ; configure heated bed #0

; Fans
M950 F0 C"fan0" ; create fan #0
M106 P0 S0 B0.1 H1 T45 ; configure fan #0
M950 F1 C"fan1" ; create fan #1
M106 P1 S0 B0.1 H1 T45 ; configure fan #1

; Tools
M563 P0 S"E0" D0 H1 F0 ; create tool #0
M568 P0 R0 S0 ; set initial tool #0 active and standby temperatures to 0C

; Miscellaneous
M501 ; load saved parameters from non-volatile memory