@oliof said in Wire Gauge for Toolboards:

with a 40W heater, a mini IR probe, single 5015 fan for cooling on an open frame corexy (ratrog V-Core Pro). The wires don't seem to get warm during prolonged use (tested with a 36h long print). I used 16 or 18 AWG wires before (speaker cables), and those had insulation that was too thick for the crimps to hold properly.

This is fairly close to what I have.
Thanks.

@bearer Thanks
I will look it over and see if makes sense to do the changes

@Nellor Your homing file probably has a Z lift.

if running rrf3 you could use daemon.g and conditional gcode to test the status and set the pin for the led accordingly. it would then run every second or so updating the led.

there are a few threads here on similar topics using the status from the object model you might find helpfull if searching a little.

@bam @sylvaindc Hi sorry I've not replied earlier, do you guys still need the files or some adjustments done?

@CaLviNx said in Duet 5 mini Feedback:

the design files on git hub can't also be wrong

The boards are manufactured from the design files so should match.

@TimV said in E3D BigBox rebuild - some issues - Duet Wifi:

Currently running v 1.19.2,

At least update to 2.05.1. Here are some instructions to update from such an old firmware.

https://forum.duet3d.com/topic/18962/firmware-not-updating?_=1609006045448

@maicolspazzini said in Mechanical filament sensor config:

But during print there are some notifications ''bad command .... '' How can I resolve?

Please create a new thread with your issue and include as much detail as poissble.

Hi Mugga,

I use the same configuration as you.

For me the following code work fine (based on your inspiration):

M308 S0 P"bedtemp" Y"thermistor" A"Bed Pad" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp M308 S4 P"e2temp" Y"thermistor" A"Bed Plate" T98801 B4185 ; configure sensor 4 as thermistor on pin e0temp M950 H0 C"bedheat" T4 ; create bed heater output on bedheat and map it to sensor 4 M140 H0 ; map heated bed to heater 0 M143 H0 P0 T0 A2 S110 C0 ; Regulate (A2) bed heater (H0) to have pad sensor below 110°C. Use Heater monitor P0 for it M143 H0 P1 T0 A0 S120 C0 ; Shut off (A1) bed heater (H0) if pad sensor exceeds 120°C. Use Heater monitor P1 for it M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit

00f90205-9576-41e8-bc3e-fcd7a38a47dd-image.png

Hi
Update:
Reheating the pins seems to have doe the trick for now.
Will need to keep a close watch on this, that the issue doesn't reappear.
Thx in advance
T.

Does the bltouch pin deploy when you send M401 and retract when you send M402 ?

You can connect several fans in parallel to each always-on fan output.

@Veti it was the infill ! / slicer settings. 2 additional Wall Perimeters solved the issue 🙂

If the duet2 can run your servo, odds are the duet3 can as well. limitation apply to can based servos only afaik.

Step/dir and rc-servo style pulse widt control ought work

@dc42 Sorry, I forgot post my config file.

; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"duet" ; set printer name M669 K1 ; select CoreXY mode ; Network ;M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP ;M586 P0 S1 ; enable HTTP ;M586 P1 S0 ; disable FTP ;M586 P2 S0 ; disable Telnet ; Drives - M569 P0.0 S1 ; physical drive 0.0 goes forwards M569 P0.1 S1 ; physical drive 0.1 goes forwards M569 P0.2 S0 ; physical drive 0.2 goes backwards M569 P0.3 S0 ; physical drive 0.3 goes backwards M569 P0.4 S0 ; physical drive 0.4 goes backwards M569 P1.0 S0 ; physical drive 1.0 goes backwards M584 X0.0 Y0.1 Z0.2:0.3:0.4 E1.0 ; set drive mapping M350 X32 Y32 Z64 E16 I1 ; configure microstepping with interpolation M92 X160.00 Y160.00 Z1600.00 E409.00 ; set steps per mm ; Calculated values from https://www.3dblog.cz/nastaveni/akcelerace-jerk-a-junction-deviation/ M201 X3200.00 Y3200.00 Z100.00 E2000.00 ; set accelerations (mm/s^2) M203 X12000.00 Y12000.00 Z300.00 E10000.00 ; set maximum speeds (mm/min) M204 P1400 ; Set printing acceleration M205 X12.00 Y12.00 Z12.00 E12.00 ; set maximum instantaneous speed changes (mm/min) M906 X1773 Y1773 Z1773 E940 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X-4:270 Y-4:270 Z0:270 ; set axis minima/maxima ; Endstops M574 X1 S1 P"!1.io1.in" ; configure sensorless endstop for low end on X M574 Y1 S1 P"!io1.in" ; configure sensorless endstop for low end on Y M574 Z1 S2 ; configure Z-probe endstop for low end on Z ; Z-Probe M950 S0 C"1.io0.out" ; create servo pin 0 for BLTouch M558 P9 C"^1.io0.in" H1.5 F240 T12000 ; set Z probe type to bltouch and the dive height + speeds G31 P1000 X36 Y-44 Z4.50 ; set Z probe trigger value, offset and trigger height M557 X32:270 Y0:226 P8 ; define mesh grid ; Heaters M308 S0 P"temp0" Y"thermistor" T90000 B4000 A"Bed" D600 ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"out1" T0 ; create bed heater output on out0 and map it to sensor 0 M140 H0 ; map heated bed to heater 0 M143 H0 S130 ; set temperature limit for heater 0 to 130C M308 S1 P"1.temp0" Y"pt1000" A"Nozzle"; configure sensor 1 as PT1000 on pin 1.temp0 M950 H1 C"1.out0" T1 ; create nozzle heater output on 1.out0 and map it to sensor 1 ;M950 H1 C"out0" T1 ; (TUNING PURPOSES - M303 only) create nozzle heater output on out0 and map it to sensor 1 M143 H1 S285 ; set temperature limit for heater 1 ; Fan M950 F0 C"!1.out1+^out1.tach" Q1000 ; create fan 0 on pin 1.out1 and set its frequency (Blower) M106 P0 S0 H-1 B0.2 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"1.out2+^out2.tach" ; create fan 1 on pin 1.out2 and set its frequency (Heatsink) M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on ; Tools M563 P0 D0 H1 F0 S"Hemera" ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined ; Miscellaneous M575 P1 S1 B57600 ; enable support for PanelDue ; Resetting Z-probe M280 P0 S160 ; Alarm Release and Push-Pin UP M280 P0 S90 ; Send PWM channel 0 the S90 (angle) command ;M290 M290 R0 S-0.040 ; Baby Z-offset M572 D0 S0.025 ; Configure pressure advance ;M564 H0 ; allow movement of axes that have not been homed M501 ; Set the active parameters to those stored in sys/config-override.g on the SD card.

@bearer said in Duet 2 Maestro and FYSETC Mini12864:

Could you just add which of the two chipsets that display uses? ST7920 or ST7565 iirc.

The Mini12864 uses the ST7565. Displays with the ST7920 such as the reprep discount one are natively supported without the need of a dedicated wiring loom.

Configuration needed:

; Enable LCD M918 P2 E-4