Mesh calibration not working or what am I doing wrong?

Dep

@infiniteloop What do you mean by synchronizing with the bed?

If you mean the transition through zero, then it is when the bed is heated.

I can’t level the bed better, it is very big and heavy. And when I heat it to 120 degrees - it distorts it a lot.

Also, when the entire chamber is heated to 45 - 50 degrees, the entire system also bends.

But I do this: I warm up the bed and chamber , wait 1-2 hours and run mesh calibration two times and compare the resulting grid. If everything is ok, I'm trying to print. This is a very long process

But every time the same thing.

I don’t understand why mesh cannot perform compensation.

jens55

@Dep, maybe I can put it in slightly different words that might make more sense.

Suppose you have 50 mm between probing points. Also suppose you are printing a part that is 50 mm long and starts on probing point one and goes to probing point two.

The mesh compensation interprets the area between point one and point two as a straight line so let's suppose point one is at 0.1 mm and point two is 0.5 mm for the offset. This means that the Duet thinks that the height at 25 mm is 0.3 mm.
The problem is that this is a guess. With a very uneven bed, your actual offset in the middle might be -0.1 or + 1.0 or whatever. The controller does not and can not know about what is actually happening in an area that was not probed and has to make an educated guess. If that guess does not reflect the true shape of the actual bed then you get a strange print.

Another way of looking at it is the mesh bed levelling can only work reasonably well if the bed does not vary wildly between probing points. It can compensate nicely if you have sufficient probing points so that the height between two adjacent probing points does not vary by a lot and the interpolation that happens between the two points can reasonably be described as a relatively straight line.

Hope that helps ....

Edit: If you were printing a model that is 50 mm * 50 mm and if you used all 121 available probe points for that small printing area, you would likely get a very nice first layer.

deckingman

@jens55 I agree in theory with what you say but from what I can gather, @Dep has a sheet of 4mm glass on top of "something" - presumably an aluminium heat spreader of some sort. In which case, I'd have thought that it's very unlikely that there are any significant peaks and troughs between any two 50mm probe points and the glass would have a fairly even curvature. In which case, interpolation between points should be reasonably accurate.

Dep

I agree with you that the smaller the distance between the points, the better the calibration.

But the glass on the table cannot be bent strongly at a distance of 50mm.

Look at the photo: why the calibration is not performed?

dgrat

Would you post some photos of your printer and the whole config.g file?

infiniteloop

@Dep

I warm up the bed and chamber , wait 1-2 hours and run mesh calibration two times and compare the resulting grid. If everything is ok, I'm trying to print.

I understand that a printer of that size is difficult to handle. Fact is that the last two height maps you published do not look bad, they are just not in sync with the bed plane. In other words: the white grid in the height maps represents the result of your bed levelling, the coloured plane (mostly blue) demonstrates the measured distances at the probing points. These two „planes“ are way too far off from each other.

Mesh grid compensation is not a substitute for proper bed levelling, ist is just an additional aid to smoothen the first layers. So, after you warm up bed and chamber, level the bed first, then, calibrate the mesh. If the resulting „planes“ do not match, something is wrong with your printer’s geometry.

fcwilt

@Dep said in Mesh calibration not working or what am I doing wrong?:

I agree with you that the smaller the distance between the points, the better the calibration.

But the glass on the table cannot be bent strongly at a distance of 50mm.

Look at the photo: why the calibration is not performed?

Hi,

Could you please print a simple 5 mm thick rectangle large enough that it includes that 6 probe points.

The irregular nature of the object you are printing may be hiding another problem.

Thanks.

Frederick

Dep

@infiniteloop The height maps are far apart because the table was not heated. Now I will make a new card on the heated table.

However, even if they do not match. I want to understand - are there any restrictions on the size of the shift?

Dep

@fcwilt
I will try to do. But it will take at least 4 hours

Dep

I heated the table. Here is the result:

RepRapFirmware height map file v2, min error -0.056, max error 1.271, mean 0.512, deviation 0.270
xmin,xmax,ymin,ymax,radius,xspacing,yspacing,xnum,ynum
450.00,950.00,120.00,620.00,-1.00,50.00,50.00,11,11
  0.210,  0.144,  0.077, -0.005, -0.047, -0.056,  0.005,  0.057,  0.157,  0.285,  0.423
  0.433,  0.364,  0.267,  0.133,  0.083,  0.066,  0.102,  0.179,  0.279,  0.408,  0.553
  0.664,  0.533,  0.419,  0.273,  0.207,  0.222,  0.234,  0.285,  0.372,  0.501,  0.646
  0.890,  0.709,  0.579,  0.430,  0.330,  0.267,  0.302,  0.367,  0.443,  0.563,  0.721
  1.078,  0.899,  0.713,  0.558,  0.449,  0.400,  0.405,  0.452,  0.515,  0.649,  0.782
  1.240,  1.019,  0.818,  0.627,  0.488,  0.458,  0.484,  0.534,  0.601,  0.694,  0.840
  1.271,  1.028,  0.831,  0.665,  0.538,  0.483,  0.478,  0.498,  0.598,  0.699,  0.806
  1.205,  0.980,  0.773,  0.632,  0.508,  0.471,  0.454,  0.509,  0.572,  0.698,  0.808
  1.080,  0.846,  0.679,  0.522,  0.405,  0.383,  0.417,  0.469,  0.556,  0.689,  0.792
  0.829,  0.671,  0.544,  0.382,  0.310,  0.332,  0.350,  0.437,  0.555,  0.698,  0.823
  0.687,  0.558,  0.428,  0.302,  0.217,  0.232,  0.278,  0.356,  0.468,  0.605,  0.752

And now I’ll try to print a 200 x 200 square ...

dgrat

M906 X1500 Y0 Z0 E1200 I100 ; Set motor currents (mA) and motor idle factor in per cent

looks weird. How does this even work? I also don't think, that test-printing makes sense currently.

M92 X100 Y160 Z1600 E157 ; Set steps per mm

I havent seen many builds like this. Can you post a photo. Why is Steps per mm all different?

Veti

I made a crude drawing what happens with a sagging x axis to the trigger height.
the drawing is a bit over the top, but its just to show the problem.

because of the curve created by the sagging the trigger heights varies, which causes incorrect heights to be reported.

Dep

@Veti Honestly, I did not understand your picture. Could be a little more detailed

Dep

Pictures of the result:

I should have made the bed a little lower, but it’s already clearly seen that the compensation is insufficient.

Dep

@dgrat said in Mesh calibration not working or what am I doing wrong?:

M906 X1500 Y0 Z0 E1200 I100

This is because the Y and Z motors are connected to an external driver.

Veti

@Dep
the images shows your over 1 meter long x axis.
it bends under its own weight

it shows your hotend assembly at 3 different positions.

at an angle in the at around 1/3 the length
not at an angle in the middle
at an angle at around 2/3 the length

because the entire hotend assembly is at an angle at position 1 and 3 the probe value will be off because in position 1 the nozzle is lower and in position 3 the nozzle is higher in comparison to the probes trigger point.

lets assume you have a trigger height of 5mm
i.e. at position 2 this is correct.
at position 1 your actual trigger height might be 6mm
at position your actual trigger height might be 4mm.

so your printer in the middle would be fine.
the further you move to the left your prints would get squashd
the further you move to the right your prints would be spaced or not stick to the bed.

p.s that bed surface looks like old scrap metal.

Dep

@Veti Now I understand what you mean.

I do not agree. The deflection of the extruder beam is almost zero. When it was mounted, we did a preload up. And checked on the line.

And even if there is a sag, then this is a hundredth of a millimeter.

The upper surface of the table is made of aluminum. To equalize and improve thermal conductivity, thermal grease was applied under the glass.

fcwilt

@Dep said in Mesh calibration not working or what am I doing wrong?:

@fcwilt
I will try to do. But it will take at least 4 hours

Thanks very much.

Frederick

Dep

@fcwilt Already done. Look above

fcwilt

@Dep said in Mesh calibration not working or what am I doing wrong?:

@fcwilt Already done. Look above

Yes. I see. Thanks very much.

I'm not sure what is going on. The numbers suggest that glass is very uneven.

The printed object seems to show extrusion problems. Around the perimeter the lines look good, even if they didn't adhere, but the infill looks strange.

The probing you did used a 50x50 (mm) grid correct?

Have you tried probing a smaller area using a 10x10 or 20x20?

I would be interested to see if such a small area exhibited the same strange numbers, when done on different areas on the glass, such as the middle versus the four corner.

Frederick