Navigation

    Duet3D Logo

    Duet3D

    • Register
    • Login
    • Search
    • Categories
    • Tags
    • Documentation
    • Order

    Help with settings...

    Tuning and tweaking
    4
    10
    72
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • gabi68
      gabi68 last edited by

      Hi to all,

      I have a Anycubic linear plus with:

      • duet 2 wifi board;
      • hayden rods;
      • smart effector;
      • PT100;
      • ultrabase;
      • on order a Zesty Nimble V2.
        I fight with this crappy prints for over a month. I really need help with some settings.
        I use Simplfy3D and a have:
      • bed temp. 70C;
      • hotend temp. 210C;
      • nozzle 0.4mm (brass);
      • extrusion multiplier - 0.95;
      • retraction 5mm;
      • speed retraction 3000 mm/min;
        -layer height 0.15mm;
      • first layer - height 110 - width 100 - speed 55;
      • raft;
      • no fan.
        Printer is calibrated (I think, maybe not). No warnings. Z probe working properly.
        Why I have this terrible results? See photos
        thumbnail 1.jpg
        thumbnail 2.jpg
      1 Reply Last reply Reply Quote 0
      • SIam
        SIam last edited by SIam

        nimble and 5mm! retract ? this is to mutch reduce this to 1 or 2 mm.
        Here you can find a guide to calibrate your extruder (step 5)
        can you post your config.g please

        Hypercube-Evolution-Hybrid, Piezo Orion, Orbiter
        Duet WiFi 1.02 or later + DueX5
        RepRapFirmware for Duet 2 WiFi/Ethernet 3.4.0beta4 (2021-09-27 11:30:36)
        Duet WiFi Server: 1.26
        Duet Web Control 3.4.0beta4 (2021-09-27)

        1 Reply Last reply Reply Quote 0
        • gabi68
          gabi68 last edited by

          Nimble is on the way. I still use the original extruder with Capricorn tube.
          config AKL.g

          1 Reply Last reply Reply Quote 0
          • SIam
            SIam last edited by

            @gabi68 said in Help with settings...:

            on order a Zesty Nimble V2.

            oh sorry i have this overseen try first to controll your calibration from the extruder

            Hypercube-Evolution-Hybrid, Piezo Orion, Orbiter
            Duet WiFi 1.02 or later + DueX5
            RepRapFirmware for Duet 2 WiFi/Ethernet 3.4.0beta4 (2021-09-27 11:30:36)
            Duet WiFi Server: 1.26
            Duet Web Control 3.4.0beta4 (2021-09-27)

            1 Reply Last reply Reply Quote 0
            • gabi68
              gabi68 last edited by

              1. Any advice for doing a better calibration besides the measurement method?
              2. "Nimble (biggest crap ever)". Why is that?
              1 Reply Last reply Reply Quote 0
              • dc42
                dc42 administrators last edited by dc42

                Assuming you are printing with PLA, I think you are printing much too hot. Try dropping the hot end temperature by 5C and 10C. A print cooling fan will help too.

                Duet WiFi hardware designer and firmware engineer
                Please do not ask me for Duet support via PM or email, use the forum
                http://www.escher3d.com, https://miscsolutions.wordpress.com

                1 Reply Last reply Reply Quote 0
                • gabi68
                  gabi68 last edited by

                  Hi David,
                  I was thinking about that and actually tried, but the extruder start skipping like the PLA was not melted properly.
                  I will try tomorrow with a lower temp.

                  1 Reply Last reply Reply Quote 0
                  • Danal
                    Danal last edited by

                    Shouldn't need a raft.

                    Layer 0 adhering says your Z calibration is OK.

                    Are you sure your PT100 is calibrated properly ? This looks like it could be a wildly wrong temperature.

                    -OR-

                    Extrusion is way off. What extruder? Have you calibrated by the measurement method with at least 100mm of movement?

                    Delta / Kossel printer fanatic

                    gabi68 1 Reply Last reply Reply Quote 0
                    • gabi68
                      gabi68 @Danal last edited by

                      @Danal
                      The machine is calibrated, I think. I will do it again today after work. PT 100 don't give any warnings. Thermal tuning saved with a M500.
                      On both attempts I saw the same behaviour, the first 15 layers are laid down beautifully. Starting with layer 16 where the infill is almost finished the gaps appear. It looks like the filament don't stick anymore on the previous layer.
                      Why is that?

                      1 Reply Last reply Reply Quote 0
                      • dc42
                        dc42 administrators last edited by

                        Are you sure that you haven't inadvertently configured your slicer to change the temperature or some other parameter at layer 16?

                        Or perhaps the nature of your model changes a lot at layer 16, e.g. changes from having large infill areas to small infill areas?

                        Duet WiFi hardware designer and firmware engineer
                        Please do not ask me for Duet support via PM or email, use the forum
                        http://www.escher3d.com, https://miscsolutions.wordpress.com

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Unless otherwise noted, all forum content is licensed under CC-BY-SA