Duet3D Logo

    Duet3D

    • Register
    • Login
    • Search
    • Categories
    • Tags
    • Documentation
    • Order

    3.b3b3 Warning after simulation

    Beta Firmware
    3
    3
    187
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • oliof
      oliof last edited by

      Good morning,
      just ran a file simulation, as I am wont to do every now and then.

      As the simulation commenced, I got a warning I've never seen before:

      4/25/2021, 9:35:33 AM 	M37 P"0:/gcodes/blade-vase.gcode"
      Simulating print of file 0:/gcodes/blade-vase.gcode
      4/25/2021, 9:39:53 AM 	File 0:/gcodes/blade-vase.gcode will print in 1h 41m plus heating time
      4/25/2021, 9:39:53 AM 	Warning: Cannot set print file finished because there is no file ID
      

      The file is sliced with superslicer (slic3r/PrusaSlicer fork), and was uploaded via the built-in upload function. Same issue with PrusaSlicer 2.3.1. Uploading via DWC yields the same error

      M122:

      M122
      === Diagnostics ===
      RepRapFirmware for Duet 3 MB6HC version 3.3beta3 (2021-04-22 16:28:03) running on Duet 3 MB6HC v0.6 or 1.0 (SBC mode)
      Board ID: 08DGM-9T66A-G63SJ-6J1D6-3SD6R-9U0BA
      Used output buffers: 6 of 40 (40 max)
      === RTOS ===
      Static ram: 149960
      Dynamic ram: 60976 of which 476 recycled
      Never used RAM 139924, free system stack 114 words
      Tasks: Linux(ready,56.0%,50) HEAT(delaying,0.1%,275) Move(notifyWait,2.9%,26) CanReceiv(notifyWait,0.2%,773) CanSender(notifyWait,0.0%,365) CanClock(delaying,0.0%,341) TMC(notifyWait,70.0%,57) MAIN(running,114.1%,649) IDLE(ready,0.0%,19), total 243.4%
      Owned mutexes: HTTP(MAIN)
      === Platform ===
      Last reset 37:40:37 ago, cause: software
      Last software reset at 2021-04-23 20:24, reason: User, none spinning, available RAM 139924, slot 1
      Software reset code 0x0012 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task Linu Freestk 0 n/a
      Error status: 0x04
      Aux0 errors 0,0,0
      Aux1 errors 0,0,0
      Step timer max interval 137
      MCU temperature: min 34.1, current 35.6, max 37.1
      Supply voltage: min 23.8, current 24.0, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
      12V rail voltage: min 12.2, current 12.2, max 12.3, under voltage events: 0
      Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/554/554, gc cycles 0
      Driver 0: position -1600, standstill, reads 33053, writes 2 timeouts 0, SG min/max 0/1023
      Driver 1: position -46400, standstill, reads 33053, writes 2 timeouts 0, SG min/max 0/554
      Driver 2: position 248000, standstill, reads 33055, writes 0 timeouts 0, SG min/max not available
      Driver 3: position 0, standstill, reads 33053, writes 2 timeouts 0, SG min/max 0/189
      Driver 4: position 0, standstill, reads 33053, writes 2 timeouts 0, SG min/max 0/173
      Driver 5: position 0, standstill, reads 33054, writes 2 timeouts 0, SG min/max 0/202
      Date/time: 2021-04-25 10:05:04
      Slowest loop: 52.83ms; fastest: 0.04ms
      === Storage ===
      Free file entries: 10
      SD card 0 not detected, interface speed: 37.5MBytes/sec
      SD card longest read time 0.0ms, write time 0.0ms, max retries 0
      === Move ===
      DMs created 125, maxWait 36437992ms, bed compensation in use: none, comp offset 0.000
      === MainDDARing ===
      Scheduled moves 204975, completed moves 204975, hiccups 0, stepErrors 0, LaErrors 0, Underruns [2, 0, 0], CDDA state -1
      === AuxDDARing ===
      Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
      === Heat ===
      Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
      Heater 0 is on, I-accum = 0.1
      Heater 1 is on, I-accum = 0.0
      === GCodes ===
      Segments left: 0
      Movement lock held by null
      HTTP* is doing "M122" in state(s) 0
      Telnet is idle in state(s) 0
      File* is idle in state(s) 0
      USB is idle in state(s) 0
      Aux is idle in state(s) 0
      Trigger* is idle in state(s) 0
      Queue* is idle in state(s) 0
      LCD is idle in state(s) 0
      SBC is idle in state(s) 0
      Daemon is idle in state(s) 0
      Aux2 is idle in state(s) 0
      Autopause is idle in state(s) 0
      Code queue is empty.
      === CAN ===
      Messages queued 345575, send timeouts 0, received 460287, lost 0, longest wait 6ms for reply type 6024, peak Tx sync delay 247, free buffers 49 (min 42)
      === SBC interface ===
      State: 4, failed transfers: 0
      Last transfer: 1ms ago
      RX/TX seq numbers: 32015/32015
      SPI underruns 0, overruns 0
      Number of disconnects: 0, IAP RAM available 0x2cf1c
      Buffer RX/TX: 0/0-0
      === Duet Control Server ===
      Duet Control Server v3.3-b3
      Code buffer space: 4096
      Configured SPI speed: 8000000 Hz
      Full transfers per second: 46.07
      Codes per second: 40.43
      Maximum length of RX/TX data transfers: 5116/1676
      

      <>Creality CR-20 IDEX Duet3 mini 5+<>RatRig V-Minion SKR RRF 1.1<>

      dc42 1 Reply Last reply Reply Quote 0
      • dc42
        dc42 administrators @oliof last edited by

        @oliof thanks. I'll ask @chrishamm to look at this.

        Duet WiFi hardware designer and firmware engineer
        Please do not ask me for Duet support via PM or email, use the forum
        http://www.escher3d.com, https://miscsolutions.wordpress.com

        1 Reply Last reply Reply Quote 1
        • chrishamm
          chrishamm administrators last edited by

          @oliof Thanks for the report, I've got a fix ready for this. It was caused by M0/M1 at the end of your print file.

          Duet software engineer

          1 Reply Last reply Reply Quote 1
          • First post
            Last post
          Unless otherwise noted, all forum content is licensed under CC-BY-SA