duet 2 wifi ona ctc dual help plz
-
Gonna need way more information.
https://forum.duet3d.com/topic/5909/guide-for-posting-requests-for-help
-
o im sorry its a corexy the only change i made to the printer are the duet 2 wifi and i put dual e3 extruders on it so it still uses all the stock spects on the ctc dual. i think it is a clone of the replicator dual. here are my g-code files that i configurated. i dont think they are right though when i go on the duet test it only shows 1 extruder and wont move anything but that extruder.
[16_1552921114458_tpre1.g](Uploading 100%) [15_1552921114458_tpre0.g](Uploading 100%) [14_1552921114458_tpost1.g](Uploading 100%) [13_1552921114458_tpost0.g](Uploading 100%) [12_1552921114458_tfree1.g](Uploading 100%) [11_1552921114458_tfree0.g](Uploading 100%) [10_1552921114458_stop.g](Uploading 100%) [9_1552921114458_sleep.g](Uploading 100%) [8_1552921114457_resume.g](Uploading 100%) [7_1552921114457_pause.g](Uploading 100%) [6_1552921114457_homez.g](Uploading 100%) [5_1552921114457_homey.g](Uploading 100%) [4_1552921114457_homex.g](Uploading 100%) [3_1552921114457_homeall.g](Uploading 100%) [2_1552921114457_config.json](Uploading 100%) [1_1552921114457_config.g](Uploading 100%) [0_1552921114457_bed.g](Uploading 100%)
-
https://www.amazon.com/CTC-Printer-Extruder-Nozzle-build/dp/B00URFFGQG this is the printer as i bought it i am still new to all this stuff if you need any thing else let me know please and thank you guys for the help
-
@twistedechos said in duet 2 wifi ona ctc dual help plz:
o im sorry its a corexy the only change i made to the printer are the duet 2 wifi and i put dual e3 extruders on it so it still uses all the stock spects on the ctc dual. i think it is a clone of the replicator dual. here are my g-code files that i configurated. i dont think they are right though when i go on the duet test it only shows 1 extruder and wont move anything but that extruder.
[16_1552921114458_tpre1.g](Uploading 100%) [15_1552921114458_tpre0.g](Uploading 100%) [14_1552921114458_tpost1.g](Uploading 100%) [13_1552921114458_tpost0.g](Uploading 100%) [12_1552921114458_tfree1.g](Uploading 100%) [11_1552921114458_tfree0.g](Uploading 100%) [10_1552921114458_stop.g](Uploading 100%) [9_1552921114458_sleep.g](Uploading 100%) [8_1552921114457_resume.g](Uploading 100%) [7_1552921114457_pause.g](Uploading 100%) [6_1552921114457_homez.g](Uploading 100%) [5_1552921114457_homey.g](Uploading 100%) [4_1552921114457_homex.g](Uploading 100%) [3_1552921114457_homeall.g](Uploading 100%) [2_1552921114457_config.json](Uploading 100%) [1_1552921114457_config.g](Uploading 100%) [0_1552921114457_bed.g](Uploading 100%)
For some reason, your file uploads haven't worked. Maybe there is a limit to how many you can upload at once. Please try again, starting with just config.g and the homing files.
Also please explain what you mean by "can not get it to work". What commands did you send, what did you expect to happen, and what actually happened?
-
when i try to home any of the axis it give me error g28 x g28 y and g28 z here are the files also. the printer will not do anything but move the extruter stepper it will not even heat the bed or the extruters. i am new to all this i dont know much about gcode at all. if you need any other files let me know thank you again for the help.
3_1552925130018_homez.g 2_1552925130018_homey.g 1_1552925130018_homex.g 0_1552925130018_config.g
-
@twistedechos said in duet 2 wifi ona ctc dual help plz:
when i try to home any of the axis it give me error
What is the error?
-
it is g28
-
but what does the error message say?
-
sorry it says g28 homing failed
-
i should specify that it is under the duettest interface idk where else to look for the erorrs
-
@twistedechos said in duet 2 wifi ona ctc dual help plz:
sorry it says g28 homing failed
Is that the only error message? If so, that indicates that you sent a G28 command to home the printer, but the commands in your homing file didn't cause the motor to move so as to trigger your homing switch.
Have you tested the motors individually? To do that, first send command G91 to select relative coordinates. Then send G1 s2 commands to command the motors. For example, G1 S2 X50 commands the X motor to move 50mm in the +X direction. Command G1 S2 X-50 commands it to move 50mm in the -X direction.
-
I think you may benefit from this guide: https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCartesianPrinter
-
i get m120
g91
g1 x-100 f6000
m121
error g0/g1 insufficient axes homed
the only thing it will let me do is click the retract and extrude extruder 1
if i can up load a video i can show you everything i think i might need to redo the reprap config or something but i dont know my min and max axis settings -
Can you post your homeall as well?
error g0/g1 insufficient axes homed
This happens when trying to move an axis before it is homed. Usually this is when the Z axis is lifted a bit to give clearance for homing X and Y.
From the FAQ: https://duet3d.dozuki.com/Wiki/FAQ
I get this error message: "Error: G0/G1: insufficient axes homed"
Recent firmware versions do not allow axes to be moved before they have been homed. The only movements allows are homing moves (G1 moves with S1 or H1 parameter) and individual motor moves (G1 moves with S2 or H2 parameter). So any Z movements that your homing files make before Z is homed should use the S2 parameter. Alternatively, add M564 H0 to config.g to allow axis movement before homing. -
This post is deleted! -
it wont let me upload the vid
-
Might need to use Dropbox or YouTube
-
https://youtu.be/ZGwYuOgqCJM here it is if you need any other info from me let me know in the mean time im going to read up on the links you sent me
-
i wonder if anyone has the original gcode files for the ctc my old board fried if i could get those i should just be able to upload them to the board right?
-
https://3dprinting.com/pricewatch/3d-printer/ctc-bizer/?fbclid=IwAR1yXJLIZn4f_zbPCmQrPTTxfIqpmlKQ0ub-9Qjie7nvzTodRKtTxSwOO3I if this helps at all this is the printer i have
