The machine is already manufactured, now the importatnye is to try, just that I have no experience with the firmware, I need help to configure.
regards
Latest posts made by samgles
-
RE: Firmware Configuration for external drivers.
-
RE: Firmware Configuration for external drivers.
The 4 independent stepper motors of the z axis are to be able to level the bed, since the printer is a big machine, how could you configure the firmware ?, I would like to use the expansion breakout to be able to control all the stepper motor, (in total 8 stepper motors).
Regards. -
RE: Firmware Configuration for external drivers.
I still do not try to use the internal drivers, because I have many nema 23 stepper motors , for example, the Z axis has 4 independent motors. Can the internal drivers control the current and amperage demand they require without damaging the card?
Regards. -
RE: Firmware Configuration for external drivers.
; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Wed Jun 05 2019 20:40:35 GMT-0500 (hora de verano central); General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves; Network
M550 P"My Printer" ; Set machine name
M552 S1 ; Enable network
M587 S"AXTEL-4B37" P"password" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S1 ; Enable FTP
M586 P2 S1 ; Enable Telnet; Drives
M569 P8 S1 ; Physical drive 8 goes forwards
M569 P7 S1 ; Physical drive 7 goes forwards
M569 P6 S1 ; Physical drive 6 goes forwards
M569 P5 S1 ; Physical drive 5 goes forwards
M584 X8 Y7 Z6:9 E5 ; Apply custom drive mapping
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z4000.00 E420.00 ; Set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z300.00 E1200.00 ; Set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z100.00 E250.00 ; Set accelerations (mm/s^2)
M906 X1900.00 Y1900.00 Z1900.00 E800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X430 Y430 Z450 S0 ; Set axis maxima; Endstops
M574 X1 Y2 S1 ; Set active high endstops; Z-Probe
M574 Z1 S2 ; Set endstops controlled by probe
M558 P9 H5 F120 T6000 ; Set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; Set Z probe trigger value, offset and trigger height
M557 X15:11 Y15:195 S20 ; Define mesh grid; Heaters
M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C; Fans
M106 P0 S0 I0 F500 H T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C; Automatic power saving
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss; Custom settings are not configured
Thank you for the attention, now i have connected all the positives of the x driver to the 5v pin on the PMW7 and the motors still not moving
-
Firmware Configuration for external drivers.
Hello, my name is Samuel Gonzalez from Mexico, I built a Cartesian 3D printer with large dimensions 800mm * 800mm * 800mm, I installed a Duet3D Wifi and a Duet expansion break board to install steppers TB6600 external drivers (these need 5V) and Nema steppers motor 23, the help I need is that I can not configure the firmware, I can not get the machine to move, I think it's a firmware configuration problem.
The distribution of the stepper motors is as follows:
X axis 1 stepper motor (nema 23)
Y axis 2 motor stepper (nema 23)
Z axis 4 stepper motor (nema 23)
Extruder 1 stepper motor (nema 17)
All the possible help is appreciated.