The card is now working. I changed to a different card (size and brand).
Latest posts made by Daniel__Santiago
-
RE: Probe Z and SD
-
RE: Probe Z and SD
I have both cables.
I use one 4-way cable for panel communication.
Ribbon cable for SD card.In the macro measurement, I should probably add the M500 command, but I don't know if this is enough.
-
RE: Probe Z and SD
-
I connected the panel according to the instructions. I will check and write.
-
In macros I have "my.gcode"
M558 I1 T6000 F1200 P3 H200;
G28;
G31 Z51;
G30;The first printout after measurement is approx.
I would like the measurement to be saved on SDcard, when the printer is turned off. -
-
Probe Z and SD
I am actually satisfied with the settings of my printer.
I have Duet WiFi v1.04c and PanelDue Duet3D 5 "I have two problems:
- I would like to use an SD card on the panel. I can't see her.
- I would like to remember and save the height measurement. Now I have to do it before each print.
; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Tue Aug 06 2019 12:19:57 GMT+0200 (czas Å“rodkowoeuropejski letni); General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M665 R260 L420 B160 H599 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them; Network
M550 P"new" ; Set machine name
M551 P"new" ; Set password; Drives
M569 P0 S1 ; Physical drive 0 goes forwards
M569 P1 S1 ; Physical drive 1 goes forwards
M569 P2 S1 ; Physical drive 2 goes forwards
M569 P3 S1 ; Physical drive 3 goes forwards
M350 X16 Y16 Z16 E32 I0 ; Configure microstepping without interpolation
M92 X321.28 Y321.80 Z321.80 E297.70 ; Set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E90000.00 ; Set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E5000.00 ; Set accelerations (mm/s^2)
M906 X1800.00 Y1800.00 Z1800.00 E1800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 Z0 S1 ; Set minimum Z; Endstops
M574 X2 Y2 Z2 S0 ; Set active low and disabled endstops; Z-Probe
M558 P0 H500 F120 T6000 ; Disable Z probe but set dive height, probe speed and travel speed
M557 R160 S20 ; Define mesh grid; Heaters
M140 H-1 ; Disable heated bed
M305 P1 T100000 B4138 R4700 X0 ; Set thermistor + ADC parameters for heater 1 and remap it to channel 0
M143 H1 S280 ; Set temperature limit for heater 1 to 280C; Fans
M106 P0 S0 I0 F500 H T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on; Tools
M563 P1 D0 H1 ; Define tool 1
G10 P1 X0 Y0 Z0 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C; Automatic saving after power loss is not enabled
; Custom settings are not configured