Zapta:
No specific dampers. I did buy a set just like you had. didn't need them.
The belts, mass of the carriage and the friction of the bushings provide plenty of dampening. Especially with the microstepping. That head has some reasonable mass, 4" square 1/4"thick Al plate, Al bearing housings 2" x 2-1/2" x 1/4" Head Flexplate for the piezo and 2-1/2" Al angle 2" long for the head mount. plus nuts,bolts and screwballs and sensors to boot. The steppers have PLENTY of torque. I got my knuckle in the way. Oh man....plenty of torque!
Latest posts made by tcoleman978
-
RE: Drive chatter
-
RE: Drive chatter
Just updated to:
Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.02 or later
Firmware Version: 2.05 (2019-12-13b1)
WiFi Server Version: 1.23
Web Interface Version: 1.22.5Saw no change.
Motors:17HS19-2004S1
1.8deg
83.6ozin
2A/phase
1.4ohm/phase
2.8V
3mH -
RE: Drive chatter
Dang already have, had to the steel was coming out.
Just ran a test at a Cura print speed of 160mm/s.
Better than I expected but still had the surging just a wider spacing. -
RE: Drive chatter
Started at 16x/no micro went to micro256 to help smooth...or not.
256x hiccups=big number (m350 x256)
16x hiccups=0 (no M350)
print and vibration same.
=== Move ===
Hiccups: 0, FreeDm: 157, MinFreeDm: 149, MaxWait: 0ms
Bed compensation in use: mesh, comp offset -0.272
=== DDARing ===
Scheduled moves: 1434, completed moves: 1425, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
This is with no M350.Oh and Zapta The motors have plenty of dampening No lost steps, this is not ringing its still there even if I go stupid slow.
-
Drive chatter
Gentle people; I have built a 3d printer. No surprise, I have a problem I can't resolve.
Back ground: Cartesian, VERY solid industrial 8020 frame.
8mm rod ways,GT2 belting 16tooth drive pulleys,84oz.in nema17 2A.
z axis dual leadscrew 8mm pitch anti-backlash, 1 drive motor ,2.25:1 drive ratio.
Piezo Z limit and probe, laser filament monitor. Modified MK10 head(80W & PT100).
MicroSwiss all metal hot end and extruder drive.
And best of all: Duet WiFi W/ 7" touchscreen.
Now the problem, The axis motors are surging, pulsing, vibrating or whatever you want to call it.
It can be seen, heard and shows up in the print.
It's also strong enough to shake the table slightly.
Originally thought it was the way bearings...super junk. replaced with plastic bushings, super smooth.
still have the surging. To eliminate the carriage I ran just the motor. Felt the surging in the shaft rotation.
It also seems to be speed dependent.Cura print speed 60mm/sec
X surge spacing .94mm (ripple distance peak to peak over a 10 peak count)
Y surge spacing 1.48mmCura print speed 20mm/sec
X surge spacing 0.34mm
Y surge spacing 0.53mmYea and different spacing between X and Y.
There is no loss of position, I only see this when my acceleration is stupid high
or my jerk is around 100 or more, no surprise.
My acceleration and max speed tested out much higher than set but I saw no reason to run that hard.
Shakes everything in the room(old house).
Also not Cura, MDI'ed G1 X100 F500....still there.
Seems to be more prominent in one direction over the other but still there.I'm lost anybody out there with the clue I need??
Starting to suspect a bad set of drivers(?! more than 1?) or the Duet/firmware.The filament definition also has Monitor, pressure advance and hardware retract parameters.
Config: ; Configuration file for Duet WiFi (firmware version 1.21) ; generated by RepRapFirmware Configuration Tool v2 on Thu Apr 25 2019 22:03:51 GMT-0400 (Eastern Daylight Time) ; General preferences G90 M83 ; Network M550 P"Spiffy" M552 S1 M586 P0 S1 M586 P1 S0 M586 P2 S0 ; Drives M569 P0 S1 M569 P1 S1 M569 P2 S1 M569 P3 S1 **** M350 X16 Y16 Z16 E16 I1 M92 X100.00 Y100.00 Z900.00 E89.73 M566 X600.00 Y600.00 Z600.00 E600.00 M203 X30000.00 Y30000.00 Z10000.00 E12000.00 M201 X400.00 Y400.00 Z800.00 E400.00 M906 X1800.00 Y1800.00 Z1800.00 E1800.00 I30 M84 S30 M350 X256 Y256 Z256 E256 **** M208 X-52.1 Y0 Z0 S1 M208 X312 Y400 Z300 S0 ;M564 S0 H0 M574 X1 Y1 S0 ; Z-Probe M574 Z1 S2 ;M558 P5 R0.4 H5 F1200 T6000 M558 P5 I1 R0.4 F800 X0 Y0 Z0 G31 P100 X0 Y0 Z-0.12 M557 X15:280 Y25:290 S20 ; Heaters ;M307 H0 B0 S1.00 M305 P0 T100000 B3950 R4700 M143 H0 S120 M305 P1 X200 R400 M143 H1 S280 M307 H0 A90.0 C700.0 D10.0 S1.00 V0.0 B0 ; Fans M106 P0 S0 I0 F500 H-1 M106 P1 S255 I0 F500 H1 T45 ; General M404 N1.75 D0.4 M375 ;M207 S0.5 R0.07 F2700 ; Tools M563 P0 S"Std Head" D0 H1 F0 G10 P0 X0 Y0 Z0 G10 P0 R0 S180 M572 D0 S0.05 M591 D0 P5 C3 R40:200 E3.0 S1