Of course- I'll attach an image and the config is below. Three 100ohm resistors in series with the LED, we originally tried PWM pin and ground but nothing was happening, so our current wiring is going into both E0 terminals:
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Jan 19 2020 10:21:10 GMT-0500 (Eastern Standard Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"My Printer" ; set printer name
; Network
;M551 P"MSDP21652" ; set password
;M552 S1 ; enable network
;M586 P0 S1 ; enable HTTP
;M586 P1 S0 ; disable FTP
;M586 P2 S0 ; disable Telnet
M552 S0 ; Turn network on
M552 S-1
M589 S"P21652" P"MSDP21652" I192.168.1.1
M552 S2
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
; When Geared Nema17 is on X axis need to change direction
;M569 P0 S0
M569 P1 S0 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S0 ; physical drive 3 goes forwards
M584 X0 Y1:3 U1 V3 Z2 E4 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
;M350 X2 Y16 Z16 E16 I1 ; configure microstepping with interpolation GEARED NEMA17
M92 X645.00 Y645.00 Z4000.00 E420.00 ; set steps per mm NOTE: This is specifically calibrated for the NEMA 17 ungeared.
;M92 X256.00 Y420.00 Z4000.00 E420.00 ; set steps per mm NOTE: This is specifically calibrated for the NEMA 17 geared.
M566 X450.00 Y450.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X10000.00 Y3000.00 Z180.00 E3001.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E150.00 ; set accelerations (mm/s^2)
M906 X1800 Y2000 Z800 E2400 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X900 Y10000 Z10000 S0 ; set axis maxima
; Endstops
M574 X1 Y0 Z0 S0 ; set active low and disabled endstops
; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20 ; define mesh grid
; Heaters
; M140 H-1 ; disable heated bed
; Fans
; Tools
M563 P0 D0 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
; Miscellaneous
T0 ; select first tool