@phaedrux
I already see one mistake, I entered 44 offset, but it should be -44. I already understand why the defined mesh grid didn't make sense. And I'm still trying to catch Z offset. So far I have it set to 1.90 and somehow it works a bit. Thank you very much, I will try to correct the mistake. Hopefully the printer will do what I wants.
Latest posts made by Pelikán Jiří
-
RE: bad autolevel
-
RE: bad autolevel
@phaedrux
Yes, they move, from the first when they make a line set in gcode, then at the first the nozzle is too high and at the second (way back) the nozzle is already correct. And I'm attaching diagnostics.=== Diagnostics ===
RepRapFirmware for STM32F4 based Boards version 3.3beta1_5 running on STM32F4
Used output buffers: 3 of 40 (21 max)
=== RTOS ===
Static ram: 30760
Dynamic ram: 68932 of which 76 recycled
Never used RAM 11408, free system stack 107 words
Tasks: NETWORK(notifyWait,200) HEAT(delaying,323) MAIN(running,424) IDLE(ready,20)
Owned mutexes: WiFi(NETWORK) HTTP(MAIN)
=== Platform ===
Last reset 00:44:38 ago, cause: [software]
Last software reset at 2021-06-09 22:03, reason: User, GCodes spinning, available RAM 11408, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00438000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 47.2, current 47.5, max 47.5
Supply voltage: min 24.0, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 8680, 2209 ok, reads 9480, writes 0, SG min/max 0/48
Driver 1: position 8680, 2209 standstill, reads 9480, writes 0, SG min/max 0/60
Driver 2: position 43, 2209 standstill, reads 9479, writes 0, SG min/max 0/16
Driver 3: position 0, 2209 ok, reads 9479, writes 0, SG min/max 0/16
Driver 4: position 0
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Date/time: 2021-06-09 22:47:53
Slowest loop: 48.72ms; fastest: 0.08ms
=== Storage ===
Free file entries: 9
SD card 0 detected
SD card longest read time 1.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: mesh, comp offset 0.000
=== DDARing ===
Scheduled moves 318, completed moves 314, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state 3
=== Heat ===
Bed heaters = 0, chamberHeaters = -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.6
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP is ready with "M122 " in state(s) 0
File is doing "G1 X126.9 Y108.1 E0.50023" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty. -
RE: bad autolevel
@pelikán-jiří I hoped that the printer would adjust the movements from the Z engine according to the map so that it would always be the same distance from the bed.
-
RE: bad autolevel
; Ender 3 Custom Start G-code G92 E0 ; Reset Extruder G28 ; Home all axes G29 S1 G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X0.1 Y20 Z0.5 F5000.0 ; Move to start position G1 X0.1 Y200.0 Z0.5 F1500.0 E15 ; Draw the first line G1 X0.4 Y200.0 Z0.5 F5000.0 ; Move to side a little G1 X0.4 Y20 Z0.5 F1500.0 E30 ; Draw the second line G92 E0 ; Reset Extruder G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X5 Y20 Z0.5 F5000.0 ; Move over to prevent blob squish
; bed.g ; called to perform automatic bed compensation via G32 ; ; generated by RepRapFirmware Configuration Tool v3.1.10+4-LPC on Tue Jan 19 2021 17:25:01 GMT+0800 (中国标准时间) M561 ; clear any bed transform G29 ; probe the bed and enable compensation
; ################# Home Z Preparation ################ G91 ; Relative mode G1 H2 Z5 F5000 ; Lower the bed G90 ; Back to absolute positioning G1 X130 Y130 F10000 ; Move to the center of the bed. Adjust to the co-ordinates required for the centre of your bed ; ################# Home Z Preparation ################ M558 F250 ; Set the probing speed G30 ; Probe a single point M558 F60 ; Set a slower probing speed G30 ; Probe a single point
-
bad autolevel
Hi I have a problem. Bed leveling works unevenly, don't you know what the problem might be? I have already managed to start the functional automatic leveling, but when I start printing, one side of the bed is too high and the other too low, because the motor balances the bed incorrectly.I attach my configurations. I will be very happy for advice.
;config.g ; Configuration file for BTT-E3-RRF (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.1.10+4-LPC on Tue Jan 19 2021 17:25:01 GMT+0800 (中国标准时间) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"BTT-E3-RRF" ; set printer name ; Network M552 S0 M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S0 ; physical drive 0 goes forwards using default driver timings M569 P1 S0 ; physical drive 1 goes forwards using default driver timings M569 P2 S1 ; physical drive 2 goes forwards using default driver timings M569 P3 S0 ; physical drive 3 goes forwards using default driver timings M584 X0 Y1 Z2 E3 ; set drive mapping M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X80.00 Y80.00 Z400.00 E93.00 ; set steps per mm M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X12000.00 Y12000.00 Z600.00 E1200.00 ; set maximum speeds (mm/min) M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2) M906 X580 Y580 Z580 E650 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X230 Y230 Z250 S0 ; set axis maxima ; Endstops M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop ;M591 D0 P7 C"e0stop" S1 R50:130 L7.0 E10 ; BTT Smart Filament Sensor ;M591 D0 P1 S1 ; Filament runout Sensor ; Z-Probe Bltouch M950 S0 C"servo0" ; create servo pin 0 for BLTouch M558 P9 C"^probe" H7 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds G31 P500 X44 Y0 Z2 ; set Z probe trigger value, offset and trigger height M557 X100:220 Y40:220 S50 ; define mesh grid ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bed" T0 ; create bed heater output on bed and map it to sensor 0 M301 P21.73 I1.54 D76.55 ; disable bang-bang mode for the bed heater and set PWM limit M307 H0 R2 D65 B1 S2.00 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S150 ; set temperature limit for heater 0 to 150C M143 H0 S150 ; set temperature limit for heater 0 to 150C M308 S1 P"e0temp" Y"thermistor" T100000 B3950 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M143 H1 S300 ; set temperature limit for heater 1 to 300C ; Fans M950 F0 C"fan0" Q1000 ; create fan 0 on pin fan0 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"fan1" Q1000 ; create fan 1 on pin fan1 and set its frequency M106 P1 S0 H1 T60 ; set fan 1 value. Thermostatic control is turned on ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined ; Miscellaneous ;M575 P1 S1 B57600 ; enable support for PanelDue M575 P1 S2 B57600 M552 S1 ; enable network M150 X2 T0 P0 M918 P1 E4 F1000000
; bed.g ; called to perform automatic bed compensation via G32 ; ; generated by RepRapFirmware Configuration Tool v3.1.10+4-LPC on Tue Jan 19 2021 17:25:01 GMT+0800 (中国标准时间) M561 ; clear any bed transform G29 ; probe the bed and enable compensation
-
RE: Auto leveling questions with toolboard
@pelikán-jiří said in Auto leveling questions with toolboard:
@jay_s_uk
About 24 mm away. And I have it set to x60And bed leveling also works unevenly, don't you know what the problem might be? I have already managed to start a functional autoleveling, but when I start printing, one side of the bed is too high and the other too low, because the motor balances the bed incorrectly.
-
RE: Auto leveling questions with toolboard
@jay_s_uk
About 24 mm away. And I have it set to x60 -
RE: Auto leveling questions with toolboard
I tried to find the error, but I have everything set up, but the meshgrid still doesn't work.