@Veti said in BL Touch Issue on 3.2 Firmware:
That was it! thanks alot!
@Veti said in BL Touch Issue on 3.2 Firmware:
That was it! thanks alot!
Just setup a bl touch on duet 2 wifi after some fiddling and browsing this forum I found most of the answers to get it to answer to commands M401/402 and macros for self test etc. So all that works, however i'm still stuck with the machine reading 1000 for the probe right after boot up. I tried inverting M558 but that didn't help.
Here is my config.g also i'm connected to pin 8 (heater 3)
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Apr 07 2020 00:35:24 GMT-0400 (Eastern Daylight Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"SK GO" ; set printer name
M667 S1 ; select CoreXY mode
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes forwards
M569 P3 S0 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X100.34 Y100.03 Z401.80 E417.43 ; set steps per mm
M566 X1800.00 Y1800.00 Z120.00 E2500.00 ; set jerk (mm/min)
M203 X9000.00 Y9000.00 Z1200.00 E5000.00 ; set max speed (mm/min)
M201 X2000.00 Y2000.00 Z250.00 E2500.00 ; set acceleration (mm/s^2)
M906 X800 Y800 Z800 E600 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
M572 D0 S0.085 ; set guesstimate pressure advance
;M593 F40 ; cancel ringing at xHz
; Axis Limits
M208 X-4:304 Y-3:312 Z 0:255 ; set axis limits
; Endstops
M574 Z0 S0 ; set active low and disabled endstops
M574 X1 Y1 S3 ; set endstops controlled by motor stall detection
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 R4700 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M307 H0 B0 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T500000 B4723 C1.196220e-7 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M950 H3 C"nil" ; Disable heater h3
; Z-Probe
M574 Z1 S2;
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 C"!zprobe.in" P9 H10 F800 T2000 ; set Z probe type to switch and the dive height + speeds
G31 P25 X26 Y0 Z-0 ; set Z probe trigger value, offset and trigger height
M557 X45:255 Y40:260 S38 ; define mesh grid
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
M501 ; Load latest
;BL Touch
M280 P0 S160 I1 ;Clear error state
M402 ;Retract BL Touch
Thanks for the help!