Problem solved, the D0 D1 solved it. Thank you very much. You have saved me a lot of time and effort.
Latest posts made by adking
-
RE: tool 2 extruder motor will not turn
-
RE: tool 2 extruder motor will not turn
My extruders are on a test stand. On my M584 line when I switch the position of my E drives, drive 0.5 works and drive 0.4 does not.
-
RE: tool 2 extruder motor will not turn
3/3/2021, 4:47:40 PM M98 P"config.g"
Error: Bad command: :
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C
Warning: Heater 3 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C
Heater 3 allowed excursion 15.0°C, fault trigger time 5.0 seconds
Warning: Heater 4 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C
Error: Pin 'out4' is not free
Error: Fan number 0 not found
Error: Pin 'out5' is not free
Error: Fan number 1 not found -
RE: tool 2 extruder motor will not turn
@Phaedrux said in tool 2 extruder motor will not turn:
M98 P"config.g"
3/3/2021, 4:47:40 PM M98 P"config.g"
Error: Bad command: :
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C
Warning: Heater 3 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C
Heater 3 allowed excursion 15.0°C, fault trigger time 5.0 seconds
Warning: Heater 4 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C
Error: Pin 'out4' is not free
Error: Fan number 0 not found
Error: Pin 'out5' is not free
Error: Fan number 1 not found -
RE: tool 2 extruder motor will not turn
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.01-RC9 running on Duet 3 MB6HC v1.01 or later
Board ID: 08DJM-956L2-G43S4-6JKD4-3S46N-TU4ADUsed output buffers: 1 of 40 (17 max)
=== RTOS ===
Static ram: 154572
Dynamic ram: 162496 of which 60 recycled
Exception stack ram used: 264
Never used ram: 75824
Tasks: NETWORK(ready,244) ETHERNET(blocked,444) HEAT(blocked,1184) CanReceiv(suspended,3824) CanSender(suspended,1484) CanClock(blocked,1428) TMC(blocked,216) MAIN(running,4220) IDLE(ready,80)
Owned mutexes:
=== Platform ===
Last reset 00:01:32 ago, cause: software
Last software reset at 2021-03-03 16:44, reason: User, spinning module GCodes, available RAM 75824 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 40.0, current 41.2, max 41.3
Supply voltage: min 24.2, current 24.2, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.2, max 12.3, under voltage events: 0
Driver 0: standstill, reads 61844, writes 14 timeouts 0, SG min/max 0/0
Driver 1: standstill, reads 61844, writes 14 timeouts 0, SG min/max 0/0
Driver 2: standstill, reads 61845, writes 14 timeouts 0, SG min/max 0/0
Driver 3: standstill, reads 61849, writes 11 timeouts 0, SG min/max 0/0
Driver 4: standstill, reads 61846, writes 14 timeouts 0, SG min/max 0/0
Driver 5: standstill, reads 61847, writes 14 timeouts 0, SG min/max 0/0
Date/time: 2021-03-03 16:46:20
Slowest loop: 5.12ms; fastest: 0.21ms
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = 3 4 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 5.54ms; fastest: 0.03ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8- Ethernet -
State: active
Error counts: 0 0 0 0 0
Socket states: 5 2 2 2 2 0 0 0
=== CAN ===
Messages sent 368, longest wait 0ms for type 0
=== Linux interface ===
State: 0, failed transfers: 0
Last transfer: 92140ms ago
RX/TX seq numbers: 0/1
SPI underruns 0, overruns 0
Number of disconnects: 0
Buffer RX/TX: 0/0-0
- Ethernet -
-
RE: tool 2 extruder motor will not turn
:; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.2 on Sat Jan 23 2021 09:40:29 GMT-0500 (Eastern Standard Time); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"ANYCUBIC MEGA X" ; set printer name; Network
M552 P192.168.2.1 S1 ; enable network and acquire dynamic address via DHCP
M553 P255.255.255.0 ; subnet mask
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S1 ; physical drive 0.1 goes forwards
M569 P0.2 S1 ; physical drive 0.2 goes forwards
M569 P0.3 S1 ; physical drive 0.3 goes forwards
M569 P0.4 S1 ; physical drive 0.4 goes forwards
M569 P0.5 S0 ; physical drive 0.5 goes forwards
M584 X0.0 Y0.1 Z0.2 E0.4:0.5 ; set drive mapping
M350 X16 Y16 Z16 E16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E420.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X305 Y305 Z300 S0 ; set axis maxima; Endstops
M574 X1 S1 P"^io0.in" ; configure active-high endstop for low end on X via pin ^io0.in
M574 Y1 S1 P"^io1.in" ; configure active-high endstop for low end on Y via pin ^io1.in
M574 Z1 S1 P"^io2.in" ; configure active-high endstop for low end on Z via pin ^io2.in; Z-Probe
M558 P5 C"^io5.in" H5 F120 T6000 ; set Z probe type to switch and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M556 S50 X0 Y0 Z0 ; set orthogonal axis compensation parameters
M557 X15:215 Y15:195 S20 ; define mesh grid; Heaters
M308 S0 P"temp0" Y"thermistor" ;configure sensor 0 as thermistor on pin temp0
M950 H0 C"out1" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S180 ; set temperature limit for heater 0 to 160C
M570 H0 P120M308 S1 P"spi.cs0" Y"thermocouple-max31856" ; configure sensor 1 as thermocouple on pin temp1
M950 H1 C"out2" T1 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S0.3 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S520 ; set temperature limit for heater 1 to 500C
M570 H1 P120M308 S2 P"spi.cs1" Y"thermocouple-max31856" ; configure sensor 2 as PT1000 on pin temp2
M950 H2 C"out3" T2 ; create nozzle heater output on out2 and map it to sensor 2
M307 H2 B0 S0.3 ; disable bang-bang mode for heater and set PWM limit
M143 H2 S520 ; set temperature limit for heater 2 to 500C
m570 H1 P120
M308 S3 P"temp1" Y"thermistor" ; configure sensor 3 as thermistor on pin temp2
M950 H3 C"out4" T3 ; create chamber heater output on out3 and map it to sensor 3
M307 H3 B0 S1.00 ; disable bang-bang mode for the chamber heater and set PWM limit
M141 P0 H3 ; map chamber to heater 3
M143 H3 S160 ; set temperature limit for heater 3 to 160C
m570 H3 120
M308 S4 P"temp2" Y"thermistor"
M950 H4 C"out5" T4
M307 H4 B0 S1.00
M141 P1 H4
M143 H4 S160
M570 H4 P120; Fans
M950 F0 C"out4" Q500 ; create fan 0 on pin out4 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"out5" Q500 ; create fan 1 on pin out5 and set its frequency
M106 P1 S0 H-1 ; set fan 1 value. Thermostatic control is turned off;TOOLS
M563 P0 S"MAIN EXTRUDER" D0.4 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M563 P1 S"SECONDARY EXTRUDER" D0.5 H2 F1 ; define tool 1
G10 P1 X10 Y0 Z0
G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C; Custom settings
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue -
tool 2 extruder motor will not turn
I am running Duet 3 with Paneldue and DWC. I have set up 2 extruders. Tool 0 and Tool 1. Tool 0 always turns and tool 1 never turns even when tool 1 is selected in DWC. Any ideas?
Thanks