@Phaedrux said in Web Control 3.2.0 - Duet 2 Wifi - Extruder0 not heating:
will
I'm so stupid...
i played all day on the settings. and then it was just incorrectly controlled by me.....
Ok. Big thx. And now i can adjust my config on 3.2...
@Phaedrux said in Web Control 3.2.0 - Duet 2 Wifi - Extruder0 not heating:
will
I'm so stupid...
i played all day on the settings. and then it was just incorrectly controlled by me.....
Ok. Big thx. And now i can adjust my config on 3.2...
Output from M122 :
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2 running on Duet WiFi 1.02 or later
Board ID: 08DGM-917DA-G4MSJ-XXXXX-XXXXX-XXXXX
Used output buffers: 3 of 24 (20 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 73124 of which 0 recycled
Never used RAM 15496, free system stack 188 words
Tasks: NETWORK(ready,157) HEAT(blocked,295) MAIN(running,466) IDLE(ready,19)
Owned mutexes: WiFi(NETWORK) HTTP(MAIN)
=== Platform ===
Last reset 00:11:20 ago, cause: software
Last software reset at 2021-01-05 19:17, reason: User, GCodes spinning, available RAM 15496, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 25.5, current 26.4, max 26.8
Supply voltage: min 24.0, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-01-05 19:28:33
Cache data hit count 840860290
Slowest loop: 8.66ms; fastest: 0.20ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.1ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is ready with "M122 " in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 41.13ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 2 of 8
- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.25
WiFi MAC address cc:50:e3:xx:xx:xx
WiFi Vcc 3.35, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 22232
WiFi IP address 192.168.5.62
WiFi signal strength -48dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0
@Phaedrux
I've don't edit the default thermister because it work and display the normal temperatur
I've used the old Firmware (2.0.4) until tomorow without any problems.
Now i want update my duet wifi board to the actual firmware.
I've installed, the "Duet2and3Firmware-3.0.zip" from the 3.0 release and update my board.
Then I updated my Board to 3.2.0 by the same way.
Because the configuration file was changed by the 3.x release.
I createt a new configuration with the RepRapFirmware Configuration Tool (online).
The headbed is heating normal, but the extruder don't heat.
On the board no voltage on E0_HEAT.
When i went down to 2.x Firmware the extruder is heating again.
What's my fault ?
I've attached my config files from 2.x and 3.2
Big thanks..
Config old Firmware with running Heater/Extruder :
config_2_x.g
Config new Firmware Heater/Extruder dont heat:
config_3_2.g