Thanks a lot
Posts made by AnWi
-
Getting position
Hi
I'm testing coding in 3.01 RC4. Is there a way to get the position from an axis? I really have tried.
I have coded an inner loop with "while iterations < 9" to create one layer and then I want to change height and repeat until a certain height.
I have read this:
https://duet3d.dozuki.com/Wiki/GCode_Meta_Commands#Section_Conditional_construct https://duet3d.dozuki.com/Wiki/Object_Model_of_RepRapFirmwarethanks
Anders -
RE: New board but no working WiFi.
Thank you very, very much!!! WiFi has started and is working now.
You made my day
Connecting...
ok B:2000.0 /0.0
Printer is now online.
ok B:2000.0 /0.0M552 S0
SENDING:M552 S0
WiFi module started
ok B:2000.0 /0.0
M587 S"RoboNaviCut" P"CutMyGrass"
SENDING:M587 S"RoboNaviCut" P"passwd"
ok B:2000.0 /0.0
M552 S1
SENDING:M552 S1
ok B:2000.0 /0.0
WiFi module is connected to access point RoboNaviCut, IP address 192.168.154.20
ok B:2000.0 /0.0
M115
SENDING:M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.02RC5(RTOS) ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2018-11-28b1
ok B:2000.0 /0.0
ok B:2000.0 /0.0 -
RE: New board but no working WiFi.
@dc42 said in New board but no working WiFi.:
M587
M587
SENDING:M587
M587: Failed to retrieve network list
Error retrieving WiFi status message: bad reply format version
[ERROR] Error retrieving WiFi status message: bad reply format version/sys/config.g
; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Fri Nov 16 2018 12:33:31 GMT+0100 (centraleuropeisk normaltid); General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves; Network
M550 P"RoboNaviCut CNC" ; Set machine name
M552 S1 ; Enable network
M587 S"RoboNaviCut" P"MyWiFiPSW" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M350 X16 Y16 Z16 I1 ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z4000.00 ; Set steps per mm
M566 X900.00 Y900.00 Z12.00 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 ; Set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 ; Set accelerations (mm/s^2)
M906 X800.00 Y800.00 Z800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X850 Y850 Z200 S0 ; Set axis maxima; Endstops
M574 X1 Y1 S3 ; Set endstops controlled by motor load detection; Z-Probe
M558 P0 H5 F120 T6000 ; Disable Z probe but set dive height, probe speed and travel speed
M557 X15:835 Y15:195 S20 ; Define mesh grid; Heaters
M140 H-1 ; Disable heated bed; Fans
M106 P0 S1 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on; Tools
; Automatic saving after power loss is not enabled
; Custom settings are not configured
-
RE: New board but no working WiFi.
@dc42 said in New board but no working WiFi.:
M587
M587
[ERROR] Printer is not online.
WiFi reported error: no known networks found
WiFi module is idleBut!!! It does not turn blue or blinking
The configuration is working! When I put the memory card in my first Duet2 WiFi it does connect to my WiFi and
If I put the memory card from my first Duet2 WiFi and put it in this one there is NO WiFi -
New board but no working WiFi.
I got my second Diet 2 Wifi two days ago but on the new card WiFi circuit refuse to start. I have been asked to do some fault findings:
When plugging in USB cable from adapter I get 3 LEDs
Red at the USB connector
Green for 3.3 Volt
Red for 5V
As expected.I have compared alla jumper settings with my working Duet 2 WiFi module and the are equal but when I power on the new board the WiFi module gives a short blue flash and nothing more. Dead quiet.
Pronterface works fine. I have flashed the latest (same) firmware again. No change. Flashed DuetWifiServer( 1.21).bin (and yes: I renamed it). Still no progress
Renamed www- directory and created a "new" www with the latest DuetWebControl (1.22.5)
This morning I checked all pins of the WiFi module with a DWM
Left row:
3.3V = 3.3V
MOSI = Low
MISO = data
SPCK = Hi
Espen = Low
EspRst = HiRight row:
Gnd = Gnd
NpSco = Hi
Edr = Hi
Iq5 = data
Tx = Hi
Rx = High but gets data about once/secondI have swapped the SD-card between the 1st Duet 2 Wifi. Both SD-card works there so my configuration should be fine. NONE of the SD card starts the WiFi unit on my new Duet 2 Wifi card.
Please help. I get the impression that the bord isn't working.
Mr Anders Wikström
Sweden